Subscribe to Our Youtube Channel
Related Manuals for AUSTRALIAN MONITOR SY2200
Summary of Contents for AUSTRALIAN MONITOR SY2200
- Page 1 PROFESSIONAL AUDIO AMPLIFIER OPERATION MANUAL SY2200 SY2400 SY2700 P R O F E SS I O N AUD IO A MP L U D I O A MP...
- Page 2 Do not parallel- or series-connect an amplifi er output Always operate the unit with the AC ground wire connected to the with any other amplifi er output. Australian Monitor Inc is not electrical system ground. Precautions should be taken so that the responsible for damage to loudspeakers for any reason.
-
Page 3: Table Of Contents
I N T R O D U C T I O N A N D C O N T E N T S Congratulations on choosing Australian Monitor for your professional I N T RO D U C TI O N amplifi... -
Page 4: F Eatu R Es
F E AT U R E S > Custom designed, 2RU heavy duty steel chassis. > Signal ground lift switch. > Front carry handles. Rear rack mount ears. > Built in limiter circuit. > Symmetrical layout - even weight distribution. >... -
Page 5: C O N Tr O L S, C O N N Ec T O Rs A N D I N D Ic Ato R S
The Synergy-2 Series differ only slightly across all models and all share the same features on their front panels. Figure 1 shows the panel layout of a SY2200 Synergy-2 amplifi er. It is similar for the SY2400, SY2700 & SY2900. -
Page 6: Rear Panel
IEC mains connector When this switch is engaged it disconnects (SY2200, SY2400) or the amplifi er is fi tted with a Pushing this switch in engages the clip limiter signal ground from the input connectors on both resettable circuit breaker (SY2700). -
Page 7: I N S Ta Ll At I O N
I N S TA L L AT I O N Power Requirements The input to your amplifi er is a balanced 3-pin Two speaker connectors are provided on the confi guration and requires all three pins to be amplifi er. Power consumption for your model of the Synergy-2 connected. - Page 8 I N S TA L L AT I O N Hum Problems Signal Ground-Lift Switch Most equipment is designed for minimum hum when used under ideal condi- When proper system hook-up has been made, you may still have some hum tions.
-
Page 9: O P Er Ati O N
O P E R AT I O N IMPORTANT: All signal source equipment should be adequately Level Matching earthed. This not only ensures your safety but everybody else’s as The normal operating position for the attenuator is the max position (fully well. -
Page 10: M A I N Te N A N Ce
M A I N T E N A N C E Only competent or qualifi ed persons should attempt any service or maintenance of your amplifi er. Your Synergy-2 Series amplifi er will need minimal maintenance. No internal adjustments need to be made to the unit to maintain optimum performance. To provide years of unhindered operation we suggest a maintenance inspection be carried out on a regular basis, say every 12 months or so. -
Page 11: S P Ec I Fi C At I O N S
S P E C I F I C AT I O N S Model: SY 2400 Common Specifi cations (To all SY2 Amplifi ers) Distortion (re 4ohm, 1dB below clip) Output Power 0.1% THD @ 1kHz THD (@ 1kHz) <0.02% 2ohm 2ohm 4ohm... - Page 12 AUSTRALIA AND NEW ZEALAND w w w. a u s t r a l i a n m o n i t o r. c o m . a u SYDNEY MELBOURNE BRISBANE ADELAIDE PERTH AUCKLAND (SA & NT SALES) (NSW &...
Need help?
Do you have a question about the SY2200 and is the answer not in the manual?
Questions and answers