Related Manuals for Diplomat PRO 700
Summarization of Contents
1. Information Before Installation
1.1 Installation Requirements
Details essential requirements for flooring, water, cooling systems, and connections.
1.2 Electrical System Requirements
Outlines electrical safety, protection devices, and general recommendations.
1.3 Operating Requirements
Specifies ambient temperature, humidity, pressure, and elevation limits.
3. Unpacking Boxes
Dental Unit Container Contents
Lists components included in the dental unit container.
Chair Container Contents
Lists components included in the chair container.
4. Prepare Place and Move Chair
4.1 Powerblock Cover
Instructions for removing the powerblock front cover.
4.2 Move Unit Into Place
4.2.1 Anchored Base
Procedure for moving and fixing the unit with an anchored base.
4.2.2 Not Anchored Base
Procedure for moving and fixing the unit with a non-anchored base.
4.2.3 Installation Board
Details on using the installation board for unit placement.
Chair Electronics Operation and Control
Safety Switch Connection
Instructions for connecting the safety switch from the assistant's arm.
Panel Fitting and Power On
Steps for fitting the front panel and powering on the unit.
Chair and Backrest Control Buttons
Explanation of how to use buttons for chair and backrest movements.
5. Cuspidor Block Installation
5.1 Cuspidor Block Holder
Procedure for fitting the cuspidor block holder using screws and bolts.
7. Post and Monitor Holder
Post Installation
Placing the post, inserting a washer, and attaching the monitor holder.
10. Monitor
Monitor Mounting
Pulling cables, screwing the monitor, and installing the monitor handle.
12. Assistant Arm
Assistant Arm Installation
Routing cables through the hole and securing the arm with a ring and screw.
13. Connecting Wires and Hoses in Cuspidor Block
13.1 Connecting Wires and Hoses from Dentist Panel
Connecting dental light cable, CAN BUS, and various tubes from the dentist panel.
13.2 Connecting Wires and Hoses from Assistant Arm
Connecting CAN BUS, safety switch, Xenos light, and saliva aspirator switch from the assistant arm.
14. Connecting Wires and Hoses in Powerblock
Powerblock Electrical Connections
Connecting CAN BUS cable and suction control wires in the powerblock.
Powerblock Hose Connections
Connecting green and blue hoses for air and water, and clear hose for headrest.
15. Assembling Accessories
15.1 Bowl
Instructions for installing the spittoon bowl, sieve, and ceramic cover.
15.2 Tray Table
Securing and leveling the tray table holder and the table itself.
15.3 Tablet Holder
Inserting and attaching the tablet holder to the dentist panel.
15.4 Napkin Holder
Instructions for installing the napkin holder.
15.5 Pneumatical Headrest
Installing the headrest and connecting the clear tube to the valve.
15.6 Assistant Console
Installing guide rollers and saliva aspirator hoses for the assistant console.
16. Finalizing Installation
16.1 Backrest
Instructions for installing the backrest upholstery and cover.
16.2 Chair Installation
Placing the chair and securing it with screws for convertible units.
16.3 Hand-rest
Placing the hand-rest and applying bumper bumpon for protection.
16.4 Putting on Covers
Moving the chair to the middle position and securing the base cover.
16.5 Powerblock Cover
Placing and securing the powerblock cover.
18. Setting Resistance of Moving Parts
18.1 Dental Light Pantograph
Adjusting the resistance of the dental light pantograph brakes.
18.2 Dental Light Post Brake
Adjusting the resistance of the dental light post brake.
18.3 Dentist Arm/Panel Brakes
Tightening the brakes for the dentist arm and panel.
18.4 Cuspidor Block Brakes
Adjusting the resistance of the cuspidor block brakes.
Need help?
Do you have a question about the PRO 700 and is the answer not in the manual?
Questions and answers