Installation - Pioneer DEH-P6200BT Installation Manual

Installation

English
DIN Front-mount
Note
1. Insert the mounting sleeve into the
• Check all connections and systems before final
installation. dashboard.
• Do not use unauthorized parts. The use of
• When installing in a shallow space, use a
unauthorized parts may cause malfunctions.
supplied mounting sleeve. If there is enough
• Consult with your dealer if installation requires
space behind the unit, use factory supplied
drilling of holes or other modifications of the
mounting sleeve.
vehicle.
• Do not install this unit where:
2. Secure the mounting sleeve by
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result of using a screwdriver to bend the
a sudden stop.
metal tabs (90°) into place.
• The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places Mounting sleeve
Dashboard
such as near the heater outlet.
• Optimum performance is obtained when the unit
182
is installed at an angle of less than 60°.
53
60°
3. Install the unit as illustrated.
• Use commercially available parts when
installing.
• When installing, to ensure proper heat dispersal
when using this unit, make sure you leave ample
Nut
space behind the rear panel and wrap any loose
Firewall or
cables so they are not blocking the vents.
metal support
Dashboard
Leave ample space
Metal strap
Screw
10 cm
Screw (M4 8)
10 cm
DIN Front/Rear-mount • Make sure that the unit is installed securely
in place. Unstable installation may cause this
This unit can be properly installed either from
unit to malfunction, such as sound skip.
"Front" (conventional DIN Front-mount) or
DIN Rear-mount
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
1. Determine the appropriate position
chassis). For details, refer to the following
where the holes on the bracket and
installation methods.
the side of the unit match.
Installation English
3. Pull the unit out of the dashboard.
2. Tighten two screws on each side.
Screw
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
Dashboard or Console
screw.
Factory radio mounting bracket
• Use either truss (5 mm × 8 mm) or flush
surface (5 mm × 9 mm) screws, depending
on the bracket screw holes.
Screw
Removing the Unit
1. Extend top and bottom of the trim
ring outwards to remove the trim
ring. (When reattaching the trim
ring, point the side with the groove
down.)
Trim ring
• Releasing the front panel allows easier access
to the trim ring.
2. Insert the supplied extraction keys
into both sides of the unit until
they click into place.
Installation English
Installing the microphone 2. Install the microphone clip on the
sun visor.
Installation notes
• With the sun visor up, install the microphone
Install the microphone in a position and clip. (Lowering the sun visor reduces the voice
recognition rate.)
orientation that will enable it to pick up the
voice of the person operating the system.
Microphone clip
CAUTION
• It is extremely dangerous to allow the microphone
lead to become wound around the steering
column or gearstick. Be sure to install the unit in
such a way that it will not obstruct driving.
When installing the microphone
on the sun visor
1. Install the microphone on the
microphone clip. Clamp
Use separately sold
clamps to secure the
lead where necessary
Microphone
inside the vehicle.
When installing the microphone
Microphone clip
on the steering column
1. Install the microphone on the
microphone clip.
Microphone
Microphone base
Fit the
Microphone clip
microphone lead
into the groove.
• Microphone can be installed without using
microphone clip. In this case, detach the
microphone base from the microphone
clip. To detach the microphone base from
microphone clip, slide the microphone base.
Installation English
2. Install the microphone clip on the
steering column.
Double-sided tape
Install the microphone clip on the
rear side of the steering column.
Clamp
Use separately sold
clamps to secure
the lead where
necessary inside the
vehicle.
Adjusting the microphone
angle
The microphone angle can be adjusted.