Table of Contents
Advertisement
CAUTION! Risk of Fire! DO NOT store instruction manuals inside fireplace cavity.
High temperatures could cause a fire.
INSTALLER: Leave this manual with the appliance, not inside the appliance.
CONSUMER: Retain this manual for future reference. Do not store inside the appliance.
NOTICE: DO NOT discard this manual!
Models:
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer's
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
Heat & Glo • 6KX, 6KX-LP, 8KX, 8KX-LP Installation Manual • 2583-980 • Rev. C • 5/23
Installation Manual
Installation and Appliance Setup
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor's phone. Follow the gas sup-
plier's instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
DANGER
DO NOT TOUCH GLASS
NEVER ALLOW CHILDREN
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and must be installed for
the protection of children and other at-risk
individuals.
Decorative barrier front must be ordered separately at
time of appliance purchase. See Section 3.B.
HOT GLASS WILL
CAUSE BURNS.
UNTIL COOLED.
TO TOUCH GLASS.
1
Advertisement
Table of Contents
Related Manuals for Heat&Glo 6KX-SJ
Summarization of Contents
Product Specific and Important Safety Information
Appliance Certification
Details the appliance's certification standards and listings.
Glass Specifications
Specifies the type of ceramic glass used and replacement procedure.
BTU Specifications
Lists input BTU/h and orifice sizes for different models.
High Altitude Installation Guidelines
Provides instructions for reducing input rate at higher elevations.
Non-Combustible Materials Definition
Defines materials that will not ignite and burn.
Combustible Materials Definition
Defines materials that can ignite and burn.
Electrical Code Compliance
Mandates compliance with National Electric Code ANSI/NFPA 70.
California Proposition 65 Warning
Warns about chemicals like benzene exposure from fuel combustion.
Massachusetts Installation Requirements
Covers CO detectors, signage, and inspection for MA installations.
Getting Started
Installation Design Considerations
Outlines key factors to consider before starting the installation process.
Wall Surface and TV Installation Guidelines
Provides recommended clearances and temperature guidelines for TVs above the appliance.
Required Tools and Supplies
Lists necessary tools and building supplies for installation.
Appliance and Component Inspection
Instructions for carefully removing and inspecting appliance parts before installation.
Framing and Clearances
Appliance Weights and Dimensions
Provides physical dimensions and weights for framing purposes.
Decorative Barrier Front Dimensions
Detailed diagrams and measurements for various decorative barrier fronts.
Appliance Location and Combustible Clearances
Guidelines for selecting appliance location and maintaining safe clearances.
Constructing the Appliance Chase
Instructions on building the chase structure for the appliance and vent.
Floor Protection Recommendations
Guidelines for protecting flooring, especially vinyl, from heat.
Termination Location and Vent Information
Approved Venting Pipe and Components
Specifies approved venting systems and components for safe operation.
Vent Termination Clearances
Minimum required clearances around the vent termination cap.
Detailed Vent Terminal Clearances
Provides U.S.A. and Canadian clearance requirements for vent terminals.
Vent Elbow Usage and Offsets
Explains the use of elbows and their effect on vent length calculations.
Venting Configuration Diagrams
Illustrates various vent configurations and rules for installation.
Vent Clearances and Framing
Vent Clearances to Combustibles
Specifies air space requirements between vent and combustible materials.
Wall Penetration Framing and Firestops
Details framing and firestop installation for wall penetrations.
Ceiling Firestop and Floor Penetration Framing
Instructions for framing ceiling and floor penetrations with firestops.
Attic Insulation Shield Installation
Requirements for installing an attic shield to prevent overheating.
Appliance Preparation
Vent Collar Preparation
Steps for preparing the appliance vent collar for pipe connection.
Heat Management System Preparation
Instructions for preparing the appliance for heat management systems.
Securing and Leveling the Appliance
Procedures for properly positioning, squaring, and securing the appliance.
Factory-Installed Non-Combustible Material
Information about the factory-installed non-combustible board above the opening.
Venting
Assembling Vent Sections
Detailed steps for connecting DVP and SLP vent pipes and ensuring seals.
Assembling Slip Sections
Instructions for assembling slip sections, including overlap and screws.
Securing Vent Sections
Methods for supporting vent sections to prevent sagging and separation.
Disassembling Vent Sections
Procedures for safely separating vent pipe sections.
Vertical Vent Termination Requirements
Guidelines for installing and sealing vertical vent termination and storm collars.
Horizontal Vent Termination Requirements
Instructions for heat shields, termination caps, and clearances for horizontal vents.
Electrical Information
General Electrical Information
Basic electrical wiring requirements, codes, and safety precautions.
IntelliFire Touch Wiring Requirements
Details wiring for the IntelliFire Touch system, including power sources.
Fan Service Procedures
Outlines how to access and service the appliance fan.
Gas Information
Fuel Conversion Procedures
Instructions for converting the appliance between different gas types.
Gas Pressure Requirements and Testing
Details gas pressure requirements and testing procedures.
Gas Line Connection
Step-by-step guide for connecting the gas supply line to the appliance.
High Altitude Gas Installation
Guidelines for adjusting input rate and orifice size at high altitudes.
Air Shutter Adjustment
Instructions on adjusting the air shutter for optimal flame appearance.
Appliance Gas Valve Service and Replacement
Procedures for servicing or replacing the appliance's gas valve.
Pilot Shield Replacement
Instructions for replacing the pilot shield on specific models.
Finishing
Facing Material Installation
Guidelines for installing facing and finishing materials around the appliance.
Television Installation Above Appliance
Refers to Section 2.B for guidelines on installing a TV above the appliance.
Mantel and Wall Projection Requirements
Specifies clearances and dimensions for combustible and non-combustible mantels.
Hearth Extension Information
States that a hearth extension is not required for these models.
Decorative Barrier Front Finishing
Details fit types and finishing methods for decorative barrier fronts.
Appliance Setup
Appliance Shipping Material Removal
Instructions for removing shipping materials and splatter guards.
Cleaning the Appliance
Recommends cleaning sawdust from the firebox and control cavity.
Brick Refractory and Glass Liner Installation
Step-by-step guide for installing the refractory panels or glass liner.
Burner Overlay Installation
Instructions for installing the burner overlay and checking ports.
Illuminated Embers Installation
Guidance on placing illuminated embers and stone media.
Burner Media and Ember Placement
Instructions on correctly placing embers to avoid blocking ports.
Log Assembly Installation
Detailed instructions and figures for placing the fireplace logs correctly.
IntelliFire Touch Control System Setup
Steps for setting up the IntelliFire Touch control system and remote.
Fixed Glass Assembly Handling
Procedures for safely removing and replacing the fixed glass assembly.
Decorative Barrier Front Installation
Instructions for installing the decorative barrier front, emphasizing approved models.
Reference Materials
Approved Vent Components List
Lists all approved vent components for DVP, SLP, and Power Vent systems.
Optional Accessories
Lists available accessories such as remote controls, heat management kits, and log sets.
Need help?
Do you have a question about the 6KX-SJ and is the answer not in the manual?
Questions and answers