Table of Contents
Advertisement
Quick Links
MODELS 8-12 AND 8-22
OPERATION AND SERVICE MANUAL
GRINDER PARTS LIST
GENERAL INSTRUCTIONS
Starting with Serial No. 5200, No. C84001 with Chain Drive
and No. C84859 with HTD Drive Belt
Note: This Catalog does not pertain to 8-12/8-22 with Plastic Gears
BIRO Designed
BIRO Built
IMPORTANT SAFETY NOTICE
This Manual contains important
safety instructions which must
be strictly followed when using
this equipment.
PTCT
8-12/8-22
No. C657-111
Advertisement
Table of Contents
Related Manuals for BIRO 8-22
Summary of Contents for BIRO 8-22
- Page 1 GRINDER PARTS LIST GENERAL INSTRUCTIONS Starting with Serial No. 5200, No. C84001 with Chain Drive and No. C84859 with HTD Drive Belt Note: This Catalog does not pertain to 8-12/8-22 with Plastic Gears BIRO Designed BIRO Built IMPORTANT SAFETY NOTICE...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Page NOTICE TO OWNERS AND OPERATORS ........SAFETY TIPS . -
Page 5: Notice To Owners And Operators
No one should use or service this machine without proper training and supervision. All operators should be thoroughly familiar with the procedures contained in this Manual. Even so BIRO cannot anticipate every circumstance or environment in which its products will be used. You, the owner and operator, must remain alert to the hazards posed by the function of this equipment particularly the ROTATING GRINDING WORM, which can severely injure an inattentive operator amputating fingers and limbs. No one under eighteen (18) years of... -
Page 6: Safety Tips
NEVER Alter This Machine From its Original Form as Shipped From Factory. DO NOT Operate Machine With Parts Missing. PROMPTLY REPLACE Any Worn or Illegible Warning Labels. ALWAYS Read Operation and Service Manual BEFORE Operating, Cleaning or Servicing. USE ONLY BIRO Parts and Accessories Properly Installed. -
Page 7: Installation
1. Read this Manual thoroughly before installation and operation. Do not proceed with installation and operation if you have any questions or do not understand anything in this Manual. Contact your local Distributor, or BIRO first. 2. Install machine on a level, solid, non-skid surface in a well-lighted work area away from children and visitors. -
Page 8: Motor Wiring And Electrical Requirements
10. Check placement of all warning labels and Manual. Machine is now ready for trained operators to process product. 11. Contact your local Distributor or BIRO directly if you have any questions or problems with the installation or operation of this machine. -
Page 9: Operation
OPERATION ROTATING GRINDING WORM TO AVOID SERIOUS PERSONAL INJURY ONLY Properly Trained Personnel Should Use This Equipment. NEVER Place Hands Into Machine Input or Output Openings. NEVER Open Machine During Operation. DO NOT Wear Gloves While Operating. DO NOT Tamper With, Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition. NEVER Operate Machine With Tray Removed. -
Page 10: Cleaning
NEVER Spray Water or Other Liquid Substances Directly at Motor, Power Switch or any Other Electrical Components. ALWAYS Thoroughly Clean Equipment at Least Daily. CLEANING THE BIRO MODEL 8-12/8-22 GRINDER 1. Disconnect grinder from power source and perform lockout/tagout procedures. 2. Remove the feed tray. -
Page 11: Maintenance
PROMPTLY REPLACE Any Worn or Illegible Labels. USE ONLY GENUINE BIRO Parts and Accessories Properly Installed. A. HIGH TORQUE DRIVE SYSTEM The Model 8-12/8-22 is driven by a High Torque Drive system for power transmissions. “No Lubrication” is required (in fact) be sure no lubricant comes in contact with the sprockets or belt. To insure a long life to the drive components: 1. -
Page 12: Tray And Case Parts Diagram
TRAY AND CASE PARTS H653-SP H653-E MC-410P CAUTION TO AVOID DAMAGE FOLLOW THESE INSTRUCTIONS 1. CHECK ROTATION Must be counter clockwise when facing main drive shaft. 2. INSERT BOWL ONLY AND TIGHTEN SECURELY WITH BOWL LOCK SCREW. Make sure bowl is tight: NO GAP IS ALLOWED 3. -
Page 13: Tray And Case Parts List And Parts Ordering
TRAY AND CASE PARTS LIST Starting with Serial No.5200, No. C84001 and No. C84859 with HTD Drive Belt. (This Catalog does not pertain to 8-12/8-22 with Plastic Gears) NOTE: SPECIFY MODEL & SERIAL NUMBER WHEN ORDERING PARTS MODEL 8-12 PARTS LIST... -
Page 14: Bowl, Frame And Motor Parts Diagram
MODEL 8-12 MISC. PARTS MODEL 8-22 MISC. PARTS C657-111 Owner/operating manual C657-111 Owner/operating manual For 8-12 Units from S/N: 5200 to S/N: 10222 For 8-22 Units from S/N: 5200 to S/N: 10377 Footnote “A”: Footnote “C”: Use C12K Bowl w/ Tray... -
Page 15: Bowl, Frame And Motor Parts List And Ordering
BOWL, FRAME & MOTOR PARTS LIST Starting with Serial No.5200, No. C84001 and No. C84859 with HTD Drive Belt. (This Catalog does not pertain to 8-12/8-22 with Plastic Gears) NOTE: SPECIFY MODEL & SERIAL NUMBER WHEN ORDERING PARTS MODEL 8-12 PARTS LIST MODEL 8-22 PARTS LIST Fig. -
Page 16: Wiring Diagrams
WIRING DIAGRAMS - 1 PHASE... - Page 17 WIRING DIAGRAMS CONTINUED - 3 PHASE...
-
Page 18: Operator's Notes
-OPERATOR’S NOTES-... -
Page 19: Operator's Signature Page
OPERATOR’S SIGNATURE PAGE WARNING READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE SIGNING BELOW MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE SERIOUS INJURY TO MYSELF AND OTHERS. NAME (PRINT) SIGNATURE SUPERVISOR’S... -
Page 20: Limited Warranty
BIRO is not responsible for electrical connection of equipment, adjustments to switch components or any other electrical requirements, which must be performed only by a certified electri- cian. BIRO is not responsible for service charges or labor required to replace any part covered by this limited warranty or for any damages resulting from misuse, abuse, lack of proper or recommended service.
Need help?
Do you have a question about the 8-22 and is the answer not in the manual?
Questions and answers