Safety Warnings; Detection Zone; System Components; Operating Instructions - STEINEL PRESENCE CONTROL PRO Manual

Operating instructions

GB
Dear Customer,
Congratulation on purchasing Please familiarise yourself with
your new STEINEL sensor and these instructions before
thank you for the confidence attempting to install the product
you have shown in us. You have because prolonged, reliable and
chosen a high-quality product trouble-free operation will only
that has been manufactured, be ensured if it is fitted and used
tested and packed with the properly.
greatest care.

Safety warnings

í Disconnect the power supply í Installing the sensor involves
before attempting any work work on the mains power
on the sensor! supply. This work must there-
í During installation, the elec-
fore be carried out profes-
tric power cable to be con- sionally in accordance with
nected must be dead. There- the applicable national wir-
fore, switch 'OFF' the power ing regulations and electrical
first and use a voltage tester operating conditions (VDE
to make sure the wiring is off 0100).
circuit.
Assembly/Installation (see chart on page 2)
The sensor is only intended for Sensor and load module come
concealed, indoor installation in ready assembled and must be
ceilings (apart from the COM 1 plugged together after fitting
AP - surface-mounted - option). the load module and setting the
A clamping-type ceiling adapter potentiometers/dip switches.
or surface-mounting adapter is
not included.

System components

Load module Twilight setting
Sensor module Time setting
Sensor base Switching output 1
Dip switches HVAC stay-'ON' time
(1) Normal/test mode Switching output 2
(2) Semi-/fully automatic mode HVAC switch-'ON' delay
(3) Button/switch Switching output 2
(4) 'ON' / 'ON'-'OFF' button Reach setting
(5) DIM option Clamping-type ceiling adapter,
Constant lighting control optional
'ON'/'OFF'
We hope your new STEINEL
sensor will bring you lasting
pleasure.
(Accessories:
Clamping-type ceiling adapter,
EAN no.: 4007841 000370
Surface-mounting adapter,
EAN no.: 4007841 000363
Guard cage,
EAN no.: 4007841 003036
Service remote control,
EAN no.: 4007841 000387
User remote control,
EAN no.: 4007841 003012
Surface-mounting adapter
IP 54, optional
Locking mechanism
Assembly/Installation
Parallel-connected
configurations
Stay-'ON' time
Orientation light
DIM option
- 20 -
How it works / Basic function
The infrared presence detectors The pyro-sensor with highly
from the Control PRO range con- advanced lens provides a square
trol lighting as well as heating, detection zone, as the typical
ventilation and air-conditioning shape of a room, in which the
(COM 2 only), e.g. in offices, smallest of movements are
schools, public buildings or at sensed. The presence detector's
home, in relation to ambient switching outputs and reach
light level and the presence of are set at the potentiometers
persons. and dip switches or by using
Presence Control PRO Presence Control PRO
IR Quattro COM 1 / COM 1 AP IR Quattro COM 2
(surface-mounted) IR Quattro HD
IR Quattro HD COM 1 /
1 switching output as COM 1.
COM 1 AP (surface-mounted)
An additional 2nd switching out-
1 switching output operating in put for operating HVAC (heating/
relation to brightness setting ventilation/air-conditioning) in re-
and presence of persons. lation to the presence of persons.
Settings: Settings:
- Brightness setting - Stay-'ON' time
- Stay-'ON' time, pulse mode, - Switch-'ON' delay
IQ mode - Room surveillance

Detection zone

Presence
radially
tangentially
Reliable presence detection a square detection zone covering
largely depends on the number, an area of 64 m
condition and arrangement of HD has 4800 switching zones that
the lens segments. The IR Quattro provide even greater precision.
with its square detection zone of These reaches can be adjusted to
49 m 2 divided up into 13 levels suit specific requirments at the
and 1272 switching zones senses setting potentiometer.
the smallest of movements. With
the optional remote control.
Presence Control has a low in-
trinsic power consumption.
Presence Control PRO
IR Quattro DIM
IR Quattro HD DIM
1 switching output operating in
relation to brightness setting
and presence of persons.
Settings:
- Brightness setting
- Stay-'ON' time, IQ mode
- Orientation light
- Constant lighting control
tangentially
radially
Presence
The square detection zone and
2 , the IR Quattro the capability of interconnecting
master/slave versions provide the
basis for creating optimum con-
figurations quickly and easily.
- 21 -