Table of Contents
Advertisement
Para español , visita:
http://www.honeywellgenerators.com/service-support/owner-support
Pour le français, visiter :
SAVE THIS MANUAL FOR FUTURE REFERENCE
Owner's Manual
Automatic Transfer Switch
100 - 200 Amp, Service Entrance / Non-Service Entrance
(Service Entrance Rated with Utility Service Circuit Breaker)
(Service Entrance Rated with Utility Service Circuit Breaker)
(Service Entrance Rated with Utility Service Circuit Breaker)
SERIAL NUMBER: _________________________
DATE PURCHASED:________________________
WWW.HONEYWELLGENERATORS.COM
http://www.honeywellgenerators.com/service-support/owner-support
For
Model Number
RXSM100A3
RXSK100A3
RXSM150A3
RXSM200A3
RXSK200A3
855-436-4636
Advertisement
Table of Contents
Related Manuals for Honeywell RXSM200A3
Summarization of Contents
Safety
Introduction
Overview of the safety section and importance of reading manual.
Safety Rules
Guidelines for safe operation and maintenance of the transfer switch.
Safety Symbols and Meanings
Explanation of hazard alert symbols (DANGER, WARNING, CAUTION, NOTE).
General Information
Unpacking
Instructions for carefully unpacking the transfer switch and inspecting for damage.
Equipment Description
Description of the automatic transfer switch and its components.
Transfer Switch Mechanism
Details on the mechanical operation and electrical connections of the transfer switch.
Utility Service Circuit Breaker (if equipped)
Specifications for utility and generator disconnect circuit breakers for different models.
Transfer Switch Data Decal
Importance of the data decal for identification and ordering parts.
Transfer Switch Enclosure
Information about the NEMA and UL rated enclosure type.
Safe Use of Transfer Switch
Key safety precautions and recommended standards for safe operation.
Load Management Options
Overview of load management systems like SACM and SMM.
Application Considerations
How load management priorities and recovery times are determined.
Installation
Introduction to Installation
Overview of the factory-wired and tested installation procedures.
Mounting
Guidelines for mounting the transfer switch enclosure vertically on a rigid structure.
Open Enclosure
Step-by-step instructions for opening the transfer switch enclosure.
Connecting Power Source and Generator Power Supply
Detailed steps for connecting utility and generator power sources.
Connecting Start Circuit Wires
Instructions for connecting generator start and sensing circuit wires.
Connecting SACM
How to connect the Smart A/C Module (SACM) for load management.
Control of Air Conditioner Load
Steps for routing and connecting thermostat cables to the SACM.
Auxiliary Contact
Information on using the normally-closed auxiliary contact for accessories.
Fault Current Label
Guidance on applying the fault current identification label for NEC compliance.
Operation
Functional Tests and Adjustments
Procedures for inspecting and testing the installation after setup.
Manual Operation
Steps for manually operating the transfer switch before electrical testing.
Close to Utility Source Side
How to manually switch the load to the utility source.
Close to Generator Source Side
How to manually switch the load to the generator source.
Return to Utility Source Side
Procedure to return the manual operating handle to the utility position.
Voltage Checks
Instructions for performing voltage measurements on power sources.
Utility Voltage Checks
Steps to check voltage levels from the utility power supply.
Generator Voltage Checks
Steps to check voltage and frequency from the generator.
Generator Tests Under Load
Procedures for testing generator performance with electrical loads applied.
Installation Summary
Verification steps for a correct installation and user education.
Shutting Generator Down While Under Load Or During A Utility Outage
Critical steps for safely shutting down the generator during outages.
Preparing for Maintenance
Safety precautions before performing maintenance on the unit.
Testing The SACM
Procedure to test the load shedding functions of the Smart A/C Module.
SACM Fuse Service
Guidance on replacing fuses in the SACM using the provided tool.
Testing The SMM
Reference to the SMM manual for its specific testing procedures.
Drawings and Diagrams
Installation Drawings
Dimensional drawings for transfer switch enclosure models.
Interconnection Drawings
Wiring diagrams showing connections between generator, ATS, and load panel.
Need help?
Do you have a question about the RXSM200A3 and is the answer not in the manual?
Questions and answers