Guarantee And Clauses - Alcatel IPTOUCH 300 User Manual

Guarantee and clauses

We,
ALCATEL BUSINESS SYSTEMS
32, avenue Kléber
92707 Colombes Cédex-France
declare that the following prducts comply with the requirements of the Directive 1999/5/EC of the European Parliament and the
Council
Alcatel Mobile IPTouch 300
Alcatel Mobile IPTouch 600
Any unauthorized modification of the products makes this declaration of conformity null and void. A copy of the original of this
declaration can be obtained from your installer.
WARNING Changes or modifications to this equipment may cause this equipment to not comply with part 15 of the FCC rules
and void the user's authority to operate this equipment.
NOTE CONCERNING THE WIRELESS TELEPHONES:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
RADIO FREQUENCY (RF) INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause any interference, please contact your intaller.
SPECIFIC ABSORPTION RATE (SAR) INFORMATION:
Your wireless handheld portable telephone is a low power radio transmitter and receiver. When it is ON, it receives and also
sends out radio frequency (RF) signals.
US
In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for hand-
held wireless phones. Those guidelines are consistent with the safety standards previously set by both U.S. and international
standards bodies:
·ANSI C95.1 (1992) American National Standards Institute
·NCRP - Report 86 (1986) National Council on Radiation Protection and Measurements
·ICNIRP (1996) International Commission on Non-Ionizing Radiation Protection;
·DHWC - Safety Code 6 Department of Health and Welfare Canada
Those standards were developed by independent scientific organizations through periodic and thorough evaluation of scientific
studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.
The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or
SAR. The SAR limit set by the FCC is 1.6W/kg.
Tests for SAR are conducted using standard operating positions specified by the FCC with the phone transmitting at its highest
certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual
SAR level of the phone while operating can be well below the maximum value.
This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the
network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a phone model is
available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the
government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn
on the body) as required by the FCC for each model. While there may be differences between the SAR levels of various phones
and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment
howtoc
Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines.
SAR information on this model phone is on file with the FCC and can be found under the
Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID OLIPT300 for Mobile IPTouch 300 and FCC ID
OL3IPT600 for Mobile IPTouch 600.
Europe and all other countries
For Europe the limit specified by Directive 1999/5/EC is 2W/kg (head and trunk).
For all countries the value of 1,6W/kg can be considered as the overall limit.
The measured SAR values are:
0.061 W/kG @ 2462 MHz (head) 0.0379 W/kG @ 2412 MHz (body) for Mobile IPTouch 300.
0.166 W/kG @ 2462 MHz (head) 0.0199 W/kG @ 2412 MHz (body) for Mobile IPTouch 600.
Phone Operation Normal Position:
Hold the phone as you would any other telephone, with the earpiece to your ear and speak into the microphone. The internal
antenna is then positioned properly.
Electro Magnetic Interference/Compatibility:
Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise
configured for electromagnetic compatibility.
Facilities:
To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio product in any facility where posted
notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.
Medical Devices
Pacemakers: The Health Industry Manufacturers Association recommends that a minimum separation of 6 inches (15 cm) be
maintained between a handheld wireless radio product and a pacemaker. These recommendations are consistent with the
independent research by, and recommendations of, Wireless Technology Research. Persons with pacemakers should:
·ALWAYS keep the radio product more than 6 inches (15 cm) from their pacemaker when the radio product is turned ON.
·Not carry the radio product in a breast pocket.
·Use the ear opposite the pacemaker to minimize the potential for interference.
·Turn the radio product OFF immediately if you have any reason to suspect that interference is taking place.
Hearing Aids: Some digital wireless radio products may interfere with some hearing aids. In the event of such interference, you
may want to consult your hearing aid manufacturer to discuss alternatives.
Other Medical Devices: If you use any other personal medical device, consult the manufacturer of your device to determine
if it is adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information.
Operational Warnings
Potentially Explosive Atmospheres: Turn off your radio product, prior to entering any area with a potentially explosive
atmosphere, unless it is a radio product type especially qualified for use in such areas (for example, Factory Mutual Approved).
Do not remove, install, or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or
fire resulting in bodily injury or even death.
The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on
boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as
grain, dust or metal powders, and any other area where you would normally be advised to turn off your vehicle
engine. Areas with potentially explosive atmospheres are often but not always posted.
Batteries: All batteries can cause property damage and/or bodily injury, such as burns if a conductive material such as jewelry,
keys, or beaded chains touches exposed terminals. The conductive material may complete an electrical circuit (short circuit) and
become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse, or other
container with metal objects.
Cleaning and Drying Considerations: Using a leather carry case may help protect the surfaces and help prevent liquids (e.g.,
rain) from entering into the interior of the radio product. This product is not waterproof, and exposing the unit to liquids may
result in permanent damage to the unit.
If your Wireless Telephone interior gets wet, then do not try to accelerate drying with the use of an oven or a dryer as this will
damage the Wireless Telephone and void the warranty. Instead, do the following: 1. Immediately power off the Wireless
Telephone. 2. Remove Battery Pack from Wireless Telephone. 3. Shake excess liquid from Wireless Telephone. 4. Place the
Wireless Telephone and Battery Pack in an area that is at room temperature and has good airflow. 5. Let the Wireless Telephone
and Battery Pack dry for 72 hours before reconnecting the Battery Pack and/or powering on the Wireless Telephone. If the
Wireless Telephone does not work after following the steps listed above, contact your dealer for servicing information.
MU-BSAA-MIPT-300-600-E700-ed00
25