Safety IMPORTANT SAFETY INSTRUCTIONS Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Warning or Caution based on the risk type. Definitions This is the safety alert symbol.
Finding Information TABLE OF CONTENTS Safety ..............2 Finding Information ..........5 Preparing for Installation ........7 Making the Gas/Electric Connection ....11 Installation ............14 Operation ............18...
Preparing for Installation VERIFY PACKAGE CONTENTS • Literature Pack • Griddle • Bolts/Washers • Simmer Plate • Burner Grate Pack • Wok Stand • Burner Set • Stainless Steel Cleaner • Gas Pressure Regulator • LP Conversion Kit • Burner Cap Pack CABINET/COUNTERTOP PREPARATION The installation of this built-in appliance must be completed by a qualified appliance technician or contractor.
Preparing for Installation IMPOR IMPOR IMPORT T T T T ANT IMPOR IMPOR Plan the installation so that the electrical connection, gas shut-off valve, and pressure regulator are accessible from the front of the cabinet and so that all of the minimum required dimensions are provided.
Preparing for Installation Base Cabinet Preparation Provide an opening in the countertop Top View as shown (see Figures 2, 3, 4, 5 and 6). Position the cutout so that minimum clearances are met. Countertop Preparation Countertop Cut-out Dimensions (when Cooktop is to be installed with Downdraft Vent Hood 36”...
Preparing for Installation Overall Dimensions - Side Views Clearance to Combustible Rear Wall Overall Dimensions Cutout Dimensions Clearance to Combustible Rear Wall Dimensions Cooktop Model E48GC76EPS 48” Min. 48” 46” 48” E36GC76EPS 36” Min. 36” 34¾” 36”...
Making the Gas/Electric Connection REQUIREMENTS WARNING WARNING WARNING WARNING WARNING Gas Supply Requirements Check your local building codes for the proper method of installation. In the absence of local codes, this appliance should be installed in accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54. Be certain that the appliance being installed is correct for the gas service being provided.
Making the Gas/Electric Connection LIQUIFIED PETROLEUM (PROPANE) GAS CONVERSION This appliance can be used with Natural Gas and Propane Gas. It is shipped from the factory for use with natural gas. A kit for converting to LP gas is supplied with your cooktop. The kit is marked “FOR LP/PROPANE GAS CONVERSION”.
Making the Gas/Electric Connection Electrical Supply Requirements The correct voltage, frequency and amperage must be supplied to the appliance from an isolated, grounded circuit which is protected by a properly sized circuit breaker or time-delay fuse. The cooktop must be connected to the power supply with copper wire only. The use of aluminum wire may result in unsatisfactory connections.
Installation INSTALLING THE COOKTOP Place and center the cooktop within the cutout. Secure the cooktop to the countertop utilizing the two (2) 1/4-20 bolts provided. Do not overtighten the screws. IMPOR IMPOR IMPORT T T T T ANT IMPOR IMPOR CONNECTING THE GAS WARNING WARNING...
Installation GAS AND ELECTRIC REQUIREMENTS TABLE The required voltage, frequency and amperage ratings are listed on the product data plate outside on the cooktop bottom. The gas and electric requirements are also shown in the table below. Model No. Electrical Total Gas type Manifold...
Installation INSTALLING THE BURNER COMPONENTS WARNING WARNING WARNING WARNING WARNING Burner Components Remove the brass burner rings, porcelain burner caps, and porcelain grates from their shipping packages. Place each burner ring onto its corresponding burner base, being certain that the four alignment tabs slide into the matching notches in the base.
Operation VERIFYING THE OPERATION WARNING WARNING WARNING WARNING WARNING Before beginning the test procedure, ensure that the gas supply is turned off at the shut-off valve, all cooktop control valves are in the “OFF” position, and all burner rings, burner caps, and grates are properly positioned on the cooktop. Rotate one knob at a time counterclockwise to the “LITE/HI”...
Operation Turn on the main gas supply to the cooktop by opening the gas shut-off valve. Test each burner separately by pressing and turning one control knob at a time counterclockwise to the “LITE/HI” position. All ignitors will spark simultaneously. (It will take approximately four seconds for ignition to occur, at which time all igniters will stop sparking.
Professional series Liquid Petroleum Gas (LPG) Conversion Kit Instructions Cooktop Models: E36GC76EPS, E48GC76EPS Model E36GC76EPS shown WARNING: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction.
Before Starting… Before converting to LPG, install the cooktop in the cabinet according to the installation instructions provided. STEP 1 Verify Kit Contents LPG Conversion Kit for Models E36GC76EPS and E48GC76EPS (36 and 48-Inch) Kit Part Number: 700208-1 Part Number Description Quantity 65480...
Professional Series Cooktop LPG Conversion Kit STEP 3 Prepare Cooktop for Conversion 3-1 If the cooktop is connected to a natural gas 3-3 Remove the grates from the top. supply line, close the gas supply valve. 3-4 Remove all of the burner caps and burner rings 3-2 Disconnect the cooktop power connector from from top of the burner heads.
STEP 4 Convert Regulator to LPG 4-1 Locate the regulator. It is underneath the 4-3 Remove the spool from the cap and insert the cooktop, below the right rear burner. opposite side. The large end of the spool must insert into the regulator first for LPG operation. 4-2 Remove the regulator cap from the regulator.
Professional Series Cooktop LPG Conversion Kit STEP 5 Disassemble Cooktop 5-1 Insert the large end of the burner ring removal 5-3 Repeat steps 5-1 and 5-2 for the remaining tool into the top of the left rear burner head. burners. Unscrew and remove the nut.
STEP 6 Replace Bypass Orifices 6-1 Make sure all knobs are in the off position. the burner location. The bypass orifice’s size is stamped on its head. 6-2 Remove all of the burner knobs from the front of the cooktop. 6-5 Insert the bypass orifice and the attached o-ring into the right side of the valve with the needle 6-3 Insert the flat-blade screwdriver into the valve...
Professional Series Cooktop LPG Conversion Kit STEP 7 Replace Main Orifices 7-1 Remove the two screws that hold the left rear 7-4 Replace the main orifice with the appropriate burner base to the chassis. size from Table 7-1. Match both the model number and the burner location.
STEP 8 Perform Pressure Tests 8-1 Connect the U-tube manometer to the LPG 8-5 Make sure all knobs on the front of the cooktop supply line. are in the off position. 8-2 With electrical power to the cooktop 8-6 Connect the U-tube manometer to the left rear disconnected, open the LPG supply valve.
Professional Series Cooktop LPG Conversion Kit Burner E36GC76EPS E48GC76EPS Location (36-Inch) (48-Inch) Left Rear HN A-0053-E HN A-0053-E Left Front HN A-0052-E HN A-0052-E Right Rear HN A-0052-E HN A-0052-E Right Front HN A-0053-E HN A-0053-E Center Rear HN A-0053-E HN A-0053-E Center Front HN A-0053-E...
STEP 10 Perform Leak Tests 10-1 Make sure that all knobs on the front of the 10-4 Re-assemble the burner heads, burner head cooktop are in the off position. nuts, burner rings, and burner caps without the spill tray in place. Be sure the igniter wire is 10-2 With electrical power to the cooktop connected for each burner head.
Figure 12-1 Conversion Label Burner Ratings and Altitude Considerations The Electrolux Professional Series cooktop is equipped burners having the following ratings: Sealed power burner(s) – input rating: 17,000 BTU per hour. Sealed power burners – input rating: 15,000 BTU per hour.
.37/9.5 Center Front HN A-0053-E .38/9.7 Model E48GC76EPS (48-Inch) The Electrolux Group USA • 250 Bobby Jones Expressway • Augusta, GA 30907 1-877-4electrolux (1-877-453-3287) • www.electroluxusa.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 1-800-688-4606 • www.electroluxca.com...