Related Manuals for EUCHNER CES-A-BTN-C07 Series
Summarization of Contents
About this document
1.1. Scope
Defines the applicability of the operating instructions to the CES-I-BP safety switch series.
1.2. Target group
Identifies design engineers, installation planners, and staff for safety components.
1.3. Key to symbols
Explains the meaning of symbols used throughout the document for warnings and information.
1.4. Supplementary documents
Lists other documents that form the complete user information for the device.
Correct Use
Correct Use Description
Details the intended application of the safety switch as an interlocking device for movable guards.
Safety Function Description
Description of Safety Function
Explains the safety function of monitoring guard position and interlocking according to EN ISO 14119.
Liability and Warranty Exclusion
Exclusion of Liability and Warranty
States that liability is excluded if conditions for correct use or safety regulations are not followed.
General Safety Precautions
General Safety Precautions
Lists essential safety measures for personnel protection and proper installation of safety switches.
Function Overview
Function Description
Describes how the safety switch monitors guard position and its operation based on actuator detection.
Diagnostic Output OD/C
Explains the diagnostic output's dual role as a door monitoring or communication output.
Door Monitoring Output OD
Details when the door monitoring output is switched on, based on actuator detection.
Communication Output OC
Describes the communication output's use for data exchange with evaluation units.
Limit-Range Monitoring
Explains how the device detects actuator drift and indicates the need for readjustment.
Switching States
Switching States Overview
Details the switching states of safety and monitoring outputs based on guard position.
Mounting Instructions
Mounting Procedures
Provides instructions and precautions for installing the safety switch and actuator.
Electrical Connection
Electrical Connection Warnings
Offers critical warnings and guidance for safe and correct electrical connection of the device.
UL/cULus Compliance
Notes about UL/cULus
Provides specific requirements for using the device with UL/cULus certifications.
Fault Handling
Safety in Case of Faults
Lists fault characteristics like reverse polarity protection and output short-circuit proofing.
Power Supply Protection
Fuse Protection for Power Supply
Explains the requirements for fuse protection based on current consumption.
Connecting Cable Requirements
Requirements for Connecting Cables
Outlines specifications and recommendations for connecting cables, including maximum length.
Connector Assignment - SB Version
Connector Assignment for CES-I-BP-...-SB
Details the pin assignment for the M12, 5-pin connector on the -SB version.
Connector Assignment - SI Version
Connector Assignment for CES-I-BP-...-SI
Details the pin assignment for the M12, 5-pin connector on the -SI version.
Connection Example
Connection Example CES-I-BP-...
Provides a schematic diagram illustrating a typical connection example for the safety switch.
BR Evaluation Unit Connection
Connection to BR Evaluation Unit
Explains how to connect the safety switch to a BR evaluation unit for data polling.
Communication Data Overview
Gives an overview of process and acyclical data transmitted by the switch.
Cyclical Data (Process Data)
Details the cyclical data transmitted by the switch, such as guard position and safety output status.
Safe Control System Operation
Notes on Operation with Safe Control Systems
Provides requirements for connecting the safety switch to safe control systems.
Setup Procedures
LED Displays
Describes the color and meaning of the STATE and DIA LEDs on the device.
Teach-in Function for Actuator
Explains the teach-in process for assigning actuators to the safety switch.
Teach-in Operation Steps
Details the step-by-step procedure for performing the teach-in operation.
Functional Check
Electrical Function Test
Outlines the procedure for checking the electrical functionality and safety of the installed device.
System Status Table
CES-I-BP System Status Table
Lists operating modes, LED indicators, outputs, and their corresponding states for diagnostics.
Technical Data - Safety Switch
Technical Data for CES-I-BP-C07-... Safety Switch
Presents detailed technical specifications for the CES-I-BP safety switch.
Radio Frequency Approvals
FCC and IC Radio Frequency Approvals
Details FCC and IC requirements and compliance statements for radio frequency emissions.
Typical System Times
Typical System Timing Parameters
Explains various system timing parameters like ready delay and switch-on time.
Dimension Drawing - Safety Switch
Dimension Drawing for CES-I-BP-C07-...
Shows dimensional drawings and important notes for the safety switch.
Technical Data - Actuator BTN
Dimension Drawing for CES-A-BTN-C07 Actuator
Displays dimensional drawings and notices for the CES-A-BTN-C07 actuator.
Operating Distances - Actuator BTN
Operating Distances & Orientations (BTN)
Provides operating distance charts for different installation orientations with the CES-A-BTN-C07 actuator.
Operating Distances - Actuator BTN (Cont.)
Operating Distances & Orientations (BTN) cont.
Continues detailing operating distances for different installation orientations with the CES-A-BTN-C07 actuator.
Technical Data - Actuator BDN
Dimension Drawing for CES-A-BDN-06-158210 Actuator
Shows dimensional drawings for the CES-A-BDN-06-158210 actuator.
Switching Distances for CES-A-BDN-06-158210 Actuator
Lists operating distances and hysteresis for the CES-A-BDN-06-158210 actuator in different orientations.
Ordering Information and Accessories
Ordering Information and Accessories
Guides users on how to find and order accessories and related materials from the EUCHNER website.
Inspection and Service
Inspection and Service Requirements
Outlines necessary inspections for long-term operation and specifies that only authorized service is permitted.
Service Contact Information
Service Contact Information
Provides contact information for service support, including phone, email, and website.
Declaration of Conformity
EU Declaration of Conformity
Presents the EU declaration of conformity, listing applicable directives and standards for the product.
Need help?
Do you have a question about the CES-A-BTN-C07 Series and is the answer not in the manual?
Questions and answers