JVC SR-L910UA - 24 Hour Time Lapse Vcr Instructions Manual page 24

6 PREPARATION
(Main menu)
MAIN MENU
PROGRAM TIMER
FUNCTION
ALARM IN
POWER LOSS
HOUR METER
CLOCK ADJUST
PRESS (SHIFT, SET)
PRESS (MENU) TO
(Date/time setting screen)
CLOCK ADJUST
YEAR
MONTH
DAY
HOUR
MINUTE
PRESS (SHIFT, SET)
PRESS (MENU) TO
CLOCK ADJUST
YEAR
MONTH
DAY
HOUR
MINUTE
PRESS (SHIFT, SET)
PRESS (MENU) TO
(Normal screen)
1 7 : 3 0 : 0 1 L24H
9 – 30 – 1998
(Menu switch <POSITION> set to L-UP)
YEAR
MONTH
HOUR
Time indication on the VCR's display
• When the power is turned off, the time is displayed. When the power is turned on, set the time display mode with the
[COUNT/CLOCK] button to display the current time.
• The first time you turn on the power, the time display shows a blinking "0:00:00".
• When the built-in backup battery capacity is low, the error indication E-10 appears on the display. Contact your local JVC
dealer to replace the built-in battery.
24
END
[SET +/-] button
2000
1
1
0
0
END
[SHIFT +/-] button and
[SET +/-] button
1998
9
30
17
30
END
[MENU] button
DAY
MINUTE
Set the date and time using the CLOCK ADJUST menu
screen.
1
Turn on this unit and the monitor and engage the Stop mode.
2
Press the [MENU] button to display the main menu screen.
3
Press the [SHIFT +] or [SHIFT -]button to select <CLOCK ADJUST>.
(Set the cursor arrow to <CLOCK ADJUST>.)
4
Press the [SET +] or [SET -] button to display the CLOCK ADJUST
screen on the monitor.
5
Select the item to be set.
• Press the [SHIFT +] or [SHIFT -] button to select the item.
[ The selected item will blink.
6
Enter the value for the selected item with the [SET +/-] button.
• Press the [SET +] button to increase the number.
• Press the [SET -] button to decrease the number.
• The setting range for the year is from 1997 to 2096.
• This VCR uses the 24-hour clock.
• If an invalid date is set, it is automatically corrected.
(e.g.) 1999-2-29 [ 1999-2-28
Repeat steps 5 and 6 until the year, month, date, hour, and minutes
have all been set.
7
End date and time setting.
• Press the [MENU] button twice.
The normal display is restored and the set date and time are shown
[
on screen. The time count starts from 00 seconds.
Note:
• If you press the [OPERATE] button after setting the date and time
without first pressing the [MENU] button, the set date and time are
canceled.
Set the date and time on the front panel display
1
Turn the power on.
2
Press the [COUNT/CLOCK] button for at least 2 seconds.
• The "year" indication blinks in the display.
3
Enter the value for the year with the [SET+] or [SET-] button.
4
Press the [SHIFT+] button: the "month" indication blinks.
• Press the [SHIFT+] or [SHIFT-] button to move the blinking section.
• Enter the value for the blinking section with the [SET+] or [SET-]
button.
5
Set the "month", "day", "hour" and "minute" with the [SHIFT+/-] and
[SET+/-] buttons.
6
When you have finished setting, press the [COUNT/CLOCK] button.
• The display returns to the clock display mode and the time count
starts from 00 seconds.