Deleting A Single Learning Key; Deleting All Learned Keys In A Specific Mode; Changing Volume Lock; Locking Volume Control To One Mode (Global Volume Lock) - Radio Shack 15-2146 - Voice Prompt Universal Remote Owner's Manual

NOTE: If the LED displays one long blink, a learning
error has occurred.Try repeating this step again until
a successful capture occurs. If the function is still
not captured, press and hold BACK to exit
programming and review the "Learning Precautions"
on the previous page. If needed, also see
"Troubleshooting" on page 11.After review, start
programming again at step 1.
7. Press 5 and repeat steps 3 through 6 for
another device and/or key or press and hold
BACK to exit programming.
D S L
ELETING A INGLE EARNING
Press and hold SETUP until you hear the
1.
programming menu, then press 5.
NOTE: If more than 15 seconds pass between key
presses, the remote says "Goodbye" and exits
programming.
At the prompt, press 2 to delete a learned
2.
function.
3. At the prompt, press 1 to delete a single
learned key.
4. At the prompt, press a device key once (i.e.,
CBL/SAT, AUX, TV, DVD, AUDIO, or VCR) to
indicate the mode where the learned key to be
deleted is stored.
5. At the prompt, press the key containing the
learned function to be deleted.
6. At the prompt, press this key again. The
remote says "Success" and returns to the
programming menu.
Press 5 and repeat steps 3 through 6 for
7.
another key or press and hold BACK to exit
programming.
D A L
ELETING LL EARNED
1. Press and hold SETUP until you hear the
programming menu, then press 5.
NOTE: If more than 15 seconds pass between key
presses, the remote says "Goodbye" and exits
programming.
2. At the prompt, press 2 to delete a learned
function.
At the prompt, press 2 to delete all the learned
3.
keys for a particular device.
4. At the prompt, press a device key (i.e., CBL/
SAT, AUX, TV, DVD, AUDIO, or VCR) to indicate
the mode to be cleared of learned keys.
5. Press the same device key again. The remote
says "Success" and returns to the prompt for
step 3.
6. Press 5 and repeat steps 3 through 5 for
another device or press and hold SETUP to exit
programming.

10 Changing Volume Lock

R S 6-
ADIO HACK IN
K
EY
K S M
EYS IN A PECIFIC ODE
-1 E S V
ASY ETUP OICE
CHANGING VOLUME LOCK
The RadioShack 6-in-1 Easy Setup Voice Remote is
set at the factory for independent volume control of
each selected device.
However, you may change the Volume Lock setting
to Global Volume Lock so that a device's volume will
be locked to one mode (e.g., to control TV volume
in all other modes).After that, if desired, you can
perform Individual Volume Unlock on a selected
device to set its volume control for independent
operation.
L V
OCKING OLUME
(G V
LOBAL OLUME
Press and hold SETUP until you hear the
1.
programming menu, then press 6.
NOTE: If more than 15 seconds pass between key
presses, the remote says "Goodbye" and exits
programming.
2. At the prompt, press 1 to lock all volume
control to a single device.
3. At the prompt, press the device key (i.e., CBL/
SAT, AUX, TV, DVD, AUDIO, or VCR) to which you
want the volume controls locked. The remote
says "Success" and returns to the prompt for
step 2.
Press and hold BACK to exit programming.
4.
Now, when you press VOL , VOL , or MUTE, the
selected device's volume will be controlled,
regardless of the mode selected. For example, if you
lock the volume to the TV, the buttons listed above
will control the volume, even if the remote is in
CBL/SAT mode.
U V
NLOCKING
S D
INGLE EVICE
U )
NLOCK
1. Press and hold SETUP until you hear the
programming menu, then press 6.
NOTE: If more than 15 seconds pass between key
presses, the remote says "Goodbye" and exits
programming.
2. At the prompt, press 2 to unlock all volume
control for a single device.
At the prompt, press the device key (i.e., CBL/
3.
SAT, AUX, TV, DVD, AUDIO, or VCR) for which you
want the volume controls unlocked. The
remote says "Success" and returns to the
prompt for step 2.
Press and hold BACK to exit programming.
4.
Now, after you select a device that has volume
unlocked, pressing VOL , VOL , or MUTE will
control the device's volume only in its own mode.
R
EMOTE
C O M
ONTROL TO NE ODE
L )
OCK
C F
OLUME ONTROL OR
(I V
NDIVIDUAL OLUME
A