HIKVISION TurboHD DS-2CE56F7T-IT Z Series User Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. TurboHD DS-2CE56F7T-IT Z Series
  6. User manual
HIKVISION TurboHD DS-2CE56F7T-IT Z Series User Manual

HIKVISION TurboHD DS-2CE56F7T-IT Z Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

DS-2CE56D7T-xITxZ Series
DS-2CE56F7T-xITxZ Series
Dome Cameras
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TurboHD DS-2CE56F7T-IT Z Series and is the answer not in the manual?

Questions and answers

Related Manuals for HIKVISION TurboHD DS-2CE56F7T-IT Z Series

Summary of Contents for HIKVISION TurboHD DS-2CE56F7T-IT Z Series

  • Page 1 DS-2CE56D7T-xITxZ Series DS-2CE56F7T-xITxZ Series Dome Cameras User Manual...

  • Page 2: Table Of Contents

    Privacy Notice ............. 3 Regulatory Information ........3 2.2.1 FCC Information ..........3 2.2.2 FCC Conditions............ 3 2.2.3 EU Conformity Statement ........4 2.2.4 Industry Canada ICES-003 Compliance ..... 4 Type I Camera Overview ........5 Type II Camera Overview ........5 Before You Start ..........

  • Page 3: Privacy Notice

    Introduction Thank you for purchasing our product. For questions or requests, please contact your dealer. This manual applies to the models below: Type Model DS-2CE56D7T-AVPIT3Z DS-2CE56F7T-AVPIT3Z Type I Camera DS-2CE56D7T-VPIT3Z DS-2CE56F7T-VPIT3Z DS-2CE56D7T-AITZ DS-2CE56F7T-AITZ Type II Camera DS-2CE56D7T-ITZ DS-2CE56F7T-ITZ This manual may contain incorrect information or printing errors, and the content is subject to change without notice.

  • Page 4: Eu Conformity Statement

    2.2.3 EU Conformity Statement This product and, if applicable, the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC. 2002/96/EC (WEEE Directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.

  • Page 5: Type I Camera Overview

    Overview • Device cables may vary by model. The cables of each type are shown below. Please refer to your actual sample. • You can debug the camera by connecting an auxiliary HD-TVI cable to the auxiliary video output. Type I Camera Overview Figure 1, Overview of Type I Camera Type II Camera Overview Figure 2, Overview of Type II Camera...

  • Page 6: Ceiling Mounting

    Ceiling Mounting 1. Attach the drill template (supplied) to the location you want to fix the camera. 2. Drill the screw holes and the cable hole in the ceiling according to the drill template. Figure 3, Drill Templates 3. Loosen the three screws on the edge of the bubble with the supplied screwdriver to remove the bubble.

  • Page 7: In-Ceiling Mounting

    8. Adjust the camera according to the figure below to get an optimum angle. 1) View the camera image with the monitor. 2) Rotate the panning table to adjust the pan direction. 3) Loosen the tilting lock screw. 4) Rotate the tilting table to adjust the tilt direction.

  • Page 8: In-Ceiling Mounting With Gang Box

    Figure 8, Fix the Camera to the Mount 5. Repeat steps 6 to 8 of the ceiling mounting section to complete the installation. 5.3.2 In-Ceiling Mounting with Gang Box Figure 9, Install the Mount 1. Repeat steps 1 to 3 of In-Ceiling Mounting Without Gang Box and secure the in-ceiling mount (supplied) to the gang box with two screws.
  • Page 9 Figure 11, Fix the Inclined Base 2. Route the cables through the in-ceiling mount hole and connect the corresponding cables. 3. Affix the camera to the in-ceiling mount with the supplied screws. Figure 12, Fix the Camera to the Base 4.

  • Page 10: Format

    Format Move the cursor to FORMAT, and press the menu button to enter the FORMAT sub menu. Set the camera format and confirm. Focus Move the cursor to FOCUS, and press the menu button to enter the FOCUS sub menu. Move the cursor to adjust the camera lens by using FOCUS+, FOCUS-, ZOOM+, and ZOOM-.

  • Page 11: Wb (White Balance)

    6.3.5 WB (White Balance) White balance is the white rendition function of the camera to adjust the color temperature according to the environment. It can remove unrealistic color casts in the image. You can set WB mode as ATW or MWB. •...

  • Page 12: Reset

    VIDEO SETTING CONTRAST SHARPNESS COLOR GAIN MIRROR DEFAULT RETURN Figure 17, Video Setting • Contrast: Enhances the difference in color and light between parts of an image. You can set the value from 1 to 10. • Sharpness: Determines the amount of detail an imaging system can reproduce.
  • Page 13 camera may reflect back into the lens causing reflection. • The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to the camera body so that the foam ring and the dome cover are attached seamlessly.

Table of Contents