Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for SOMFY Glydea WT
Summarization of Contents
Compatibility chart
Compatibility chart, Motor / Remote-sensors
Details motor and remote-sensor compatibility across various ranges and power types.
Power connection
Power connections: Applications with RTS integrated motors
Illustrates power connection methods for WireFree, 24V DC, and 230V AC motors.
RTS Motors - programming and Basic setting
1 Connect the RTS transmitter to the motor
Guides on connecting the RTS transmitter to the motor for programming.
2 Check the motor rotation direction
Procedure to verify the motor's rotational direction.
3 Change motor rotation direction if needed
Instructions for reversing motor rotation direction if necessary.
4 Place the blind in the desired UP position
Guides on positioning the blind to its upper limit.
5 Set the UP position
Steps to set the upper limit position for the blind.
6 Set the DOWN position
Steps to set the lower limit position for the blind.
7 Confirm end limit setting
Confirms the successful setting of upper and lower limits.
8 Recording an RTS transmitter
Process for pairing an RTS transmitter with the motor.
1 Adjusting the DOWN limit
Detailed steps for fine-tuning the blind's lower limit.
1 Adjusting the UP limit
Detailed steps for fine-tuning the blind's upper limit.
Setting My position for NON TILT products
Setting a preferred 'My' position for non-tilt blinds.
Setting My position for TILT products
Setting a preferred 'My' position for tilt blinds.
1 Remove programmed My position
Procedure to delete a previously set 'My' position.
Set blind mode: Roller or Venetian
Configures the motor's operating mode for roller or venetian blinds.
Wired RTS receivers, 24 VDC
Wiring
Diagrams illustrating wiring for DC RTS and Integrated DC RTS receivers.
24 V RTS Receivers - Programming and basic settings
Setting from the RTS receiver
Instructions for programming the RTS receiver directly.
Setting from the RTS remote control
Instructions for programming using the RTS remote control.
Set type of blind: Roll up or Tilt and Li
Configures the receiver for roller or tilt and lift blind types.
Change the motor rotation direction
Steps to adjust the motor's rotation direction.
Set the time for open and close movement
Sets specific timing for blind opening and closing movements.
5 Set the down movement time
Configures the precise time for the blind's downward movement.
7 Set the up movement time
Configures the precise time for the blind's upward movement.
11 Close time setting of open and close movements
Finalizes the programmed open and close movement times.
12 Confirm the time setting of open and close movements
Verifies the programmed timing for open and close operations.
Modify the MY position, in Tilt & li mode
Adjusts the 'My' position for tilt and lift applications.
Modify the MY position, in Roll up mode
Adjusts the 'My' position for roll up applications.
Remove a programmed MY-position
Procedure to delete a saved 'My' position.
Activating the motor Run timer
Enables the motor's run timer function.
Add or remove transmitters
Add a transmitter
Steps to add a new RTS transmitter to the system.
Remove an assigned transmitter
Procedure for removing an existing transmitter from the system.
Replace lost transmitter
Instructions for replacing a lost or non-functional transmitter.
Sonesse 40 WT
Setting of end limits
Guides on adjusting the motor's stop limits for precise operation.
Glydea, Curtain track
Recommendations
Important notes on bracket spacing and mounting distances.
Motor cable output options
Illustrates different motor cable output configurations.
Attach motor to rail
Step-by-step guide for mounting the motor onto the curtain track.
Wiring guide DCT & RTS
Provides wiring instructions for DCT and RTS systems.
Programming instruction
General steps for programming Glydea curtain track motors.
Setting My position
Procedure to set a preferred 'My' position for the curtain.
Re-adjustment of end -limits
Guides on adjusting or correcting the end limits.
Set Touch motion or manual over ride mode
Configures touch control and manual override functions.
Set track speed, default speed = 20 cm/s
Adjusts the speed settings for the curtain track movement.
Add transmitter
Instructions for adding a new transmitter to the system.
Reset motor to factory mode, erase all settings
Restores the motor to its default factory settings.
Wiring control unit to Glydea DCT
Details on connecting the control unit to the Glydea DCT.
Glydea DCT
Programming instruction for Glydea DCT
Specific programming steps for the Glydea DCT system.
Modify motor rotation direction, if needed
Adjusting the motor's rotation direction for Glydea DCT.
Re-adjustment of end -limits
Correcting or re-setting the end limits for Glydea DCT.
Set Touch motion or manual over ride mode
Configures touch control and manual override for Glydea DCT.
Reset motor to factory mode, erase all settings
Restores Glydea DCT motor to factory default settings.
Glydea WT
Programming instruction
General programming guidelines for Glydea WT.
Modify motor rotation direction, if needed
Adjusting the motor rotation direction for Glydea WT.
Back release setting
Configuration related to back release functionality.
Reset motor to factory mode, erase all settings
Resets the Glydea WT motor to its factory defaults.
Wiring instruction for Glydea WT
Provides wiring diagrams for Glydea WT installation.
Additional function
1 Deactivate and activate privacy function
Controls the activation and deactivation of the privacy function.
Program sun disappearing position
Sets a specific position for the blind when sun is detected.
Set the motor speed
Adjusts the operational speed of the motor.
Set the tilt speed / scroll wheel step
Configures the speed for tilt or scroll wheel adjustments.
Set the tilt speed / scroll wheel step
Configures the speed for tilt or scroll wheel adjustments.
To decrease speed
Procedure to reduce motor or scroll wheel speed.
To increase speed
Procedure to increase motor or scroll wheel speed.
Modify motor rotation direction
Changes the direction of motor rotation.
Modify scroll wheel rotation direction
Adjusts the rotation direction for the scroll wheel.
Sonesse 30 DCT
Wiring
Wiring instructions for the Sonesse 30 DCT.
Setting type of blind
Configures the Sonesse 30 DCT for different blind types.
Setting of rolling speed
Adjusts the rolling speed for the Sonesse 30 DCT.
Setting of tilt speed
Adjusts the tilt speed for the Sonesse 30 DCT.
Reset motor in Factory mode
Resets the Sonesse 30 DCT motor to factory defaults.
24 V Wired controls for Roll up application
Setting of My positions
Sets preferred 'My' positions for roll-up applications.
24V Wired control for Tilt & Li applications
Adjust tilt speed
Configures the speed for tilting blind slats.
Set automatic slat up-tilting
Enables automatic adjustment of slat tilt angles.
Set My position - from UP end limit
Sets a 'My' position starting from the upper end limit.
Sunis RTS, Adding and setting
Conditions
Prerequisites and conditions for adding and setting the Sunis RTS sensor.
Add a sensor for exterior installation
Steps to add the sun sensor for external mounting.
Enter programming mode
Puts the sensor into programming mode.
Connect sun sensor
Procedure for connecting the sun sensor.
Check Sun mode ON or OFF
Verifies if the sun mode is active or inactive.
Check and installation
Guides on installation and initial checks of the sensor.
Switch the Demo mode OFF
Turns off the demonstration mode for the sun sensor.
Explanations of LED signals
Interprets the meaning of different LED indicators on the sensor.
Thermosunis Indoor Wirefree RTS, Adding and setting
Usage
Overview of the different usage modes for the sensor.
Add interior sun sensor
Steps to add the sun sensor for interior mounting.
Connect sun sensor
Procedure for connecting the indoor sun sensor.
Mounting of Thermosunis Indoor Wire free RTS
Instructions for physically mounting the indoor sun sensor.
Usage options for Thermosunis Indoor Wirefree RTS
Details the different operational modes and settings.
Setting for exterior blinds, screens or roller shutters
Configuration for outdoor applications.
Setting A for interior blinds
Configuration mode 'A' for interior blinds.
Setting B for interior blinds
Configuration mode 'B' for interior blinds.
Get started with Thermosunis Indoor Wire free RTS
Initial guidance for setting up the indoor sun sensor.
Activate the sensor
Steps to activate the sun sensor.
1 Put the RTS motor / receiver in programming mode
Enters the motor/receiver into programming mode.
2 Connect the sensor
Connects the sensor to the motor/receiver.
Erase the sensor from the motor
Removes the sensor's association from the motor.
Setting of the sensitivity (threshold values)
Adjusts sensor sensitivity levels and threshold values.
DEMO mode
Explains the function and use of the demonstration mode.
Chronis Smart RTS
Explanation of display and key functions
Details the timer's display interface and button functions.
Programming options
Overview of available programming features like week programs and security.
Chronis Smart RTS
Basic principles
Fundamental information and prerequisites for using the timer.
Chronis Smart RTS (wireless timer)
Details on the wireless timer's components and initial setup.
1 Setting current time
Procedure to set the current time on the timer.
2 Setting current date
Procedure to set the current date on the timer.
3 Setting UP time
Configures the programmed UP time for the blind.
3.1 Setting the 1st UP time to a fixed time
Sets a specific UP time for the first daily command.
4.1 Setting time shi and time limit for COSMIC DOWN time
Adjusts time shift and limits for COSMIC DOWN function.
4.2 Deactivating the COSMIC function
Disables the COSMIC function for DOWN time.
4.3 Setting the DOWN time
Configures the programmed DOWN time for the blind.
4.4 Activating the COSMIC function
Enables the COSMIC function for DOWN time.
5.1 Activating the SECurity function
Enables the security function for presence simulation.
5.2 Deactivating the SECurity function
Disables the security function for presence simulation.
6.1 Deactivating the programmed UP and DOWN times
Disables programmed UP/DOWN times.
6.2 Activating the programmed UP and DOWN times
Enables programmed UP/DOWN times.
7 Special settings for use with a separate RTS receiver for window coverings DC RTS and RTS 2.5 DC modules
Advanced settings for integrating with specific RTS receivers.
Chronis Comfort RTS
Basic principles
Foundational information about motor adjustment and timer connection.
Explanation of display and key functions
Details the timer's display interface and button functions.
Programming options
Overview of programming features like week programs and security.
Chronis Comfort RTS
Basic principles
Fundamental information and prerequisites for using the timer.
Chronis Comfort RTS (wireless timer)
Details on the wireless timer's components and initial setup.
1 Setting current time
Procedure to set the current time on the timer.
2 Setting current date
Procedure to set the current date on the timer.
3 Setting UP time
Configures the programmed UP time for the blind.
3.1 Setting the 1st UP time to a fixed time
Sets a specific UP time for the first daily command.
3.2 Setting the 2nd UP time to a fixed time
Sets a specific UP time for the second daily command.
3.3 Activating the Cosmic UP function
Enables the COSMIC function for UP time.
3.4 Setting time shi and time limit for COSMIC UP time
Adjusts time shift and limits for COSMIC UP function.
3.5 Deactivating the COSMIC UP function
Disables the COSMIC function for UP time.
4 Setting the DOWN time
Configures the programmed DOWN time for the blind.
4.1 Setting time shi and time limit for COSMIC DOWN time
Adjusts time shift and limits for COSMIC DOWN function.
4.2 Deactivating the COSMIC DOWN function
Disables the COSMIC function for DOWN time.
4.3 Setting the 1st DOWN time to a fixed time
Sets a specific DOWN time for the first daily command.
4.4 Setting the 2nd DOWN time to a fixed time
Sets a specific DOWN time for the second daily command.
4.5 Activating the COSMIC function for the 1st DOWN time
Enables the COSMIC function for the first DOWN time.
5 Light sensor
Category for light sensor setup and activation.
5.1 Activating the light sensor
Procedure to activate the light sensor.
5.2 Deactivating the light sensor
Procedure to deactivate the light sensor.
6.1 Activating the SECURITY mode
Enables the security mode for presence simulation.
6.2 Deactivating the SECURITY mode
Disables the security mode for presence simulation.
7.1 Deactivating the programmed UP and DOWN times
Disables programmed UP/DOWN times.
7.2 Activating the programmed UP and DOWN times
Enables programmed UP/DOWN times.
8 Special settings for use with separate RTS receiver for window coverings DC RTS and RTS 2.5 DC modules
Advanced settings for specific RTS receiver integrations.
9 Time control for intermediate position (MY position)
Controls the blind's movement to intermediate positions via time commands.
9.1 Time command for the intermediate position in combination with UP time, DOWN time and the “light command”
Sets intermediate positions using time or light commands.
Telis 6 Chronis RTS
6-channel transmitter with built-in timer
Description of the 6-channel remote with timer capabilities.
Product benefits
Highlights key advantages and features of the remote control.
Composition
Lists the components included with the Telis 6 Chronis RTS.
Display in manual mode
Explains the display information shown in manual mode.
Display in automatic mode
Explains the display information shown in automatic mode.
Getting started
Basic steps to begin using the remote control.
Installing the batteries
Instructions for installing the remote control batteries.
Remote control set-up
Initial configuration process for the remote control.
Next parameters
Details the sequence of parameters to be set during setup.
Naming the 6 channels
Procedure for assigning names to the remote's channels.
Adding Telis 6 Chronis RTS
Steps to pair the remote control with motors or receivers.
Erasing Telis 6 Chronis RTS
Procedure to remove the remote control's pairing.
Setting tilt mode
Configures the tilt mode for blinds with movable slats.
Programming the days of the week (automatic mode)
Sets up automatic commands for each day of the week.
Choosing the day to be programmed
Selects the specific day for programming automatic commands.
Creating an automatic command
Defines a new automatic command sequence.
Selecting channels
Assigns commands to specific channels or groups.
Selecting command
Chooses the type of command to be programmed.
Copying the programme from one day to another day
Copies programmed schedules from one day to another.
Erasing an automatic command
Removes a previously created automatic command.
Switching between automatic and manual
Changes the operating mode between automatic and manual.
Manual mode
Details the functionality and use of manual mode.
Controlling the channels
Instructions for operating individual channels.
Automatic modus
Explains the automatic control features and programming.
Activating/deactivating the sun function
Enables or disables the sun function for automatic commands.
The “Presence simulation” function
Activates or deactivates the presence simulation feature.
Changing the general remote control parameters
Adjusts overall remote control settings and parameters.
Controlling products
Basic operations for controlling connected products.
Setting the preferred position (‘my’)
Sets a specific preferred position ('My') for a product.
Using the preferred position
Activates the previously set preferred position.
Attaching the Telis 6 Chronis RTS to the wall
Instructions for mounting the remote control bracket.
Tips and recommendations
Provides helpful advice and troubleshooting tips.
Technical data
Lists the technical specifications of the device.
Dimensions
Provides the physical dimensions of the remote control.
Programming Moco DCE
For products equipped with LWE motors
Context for programming Moco DCE with LWE motors.
Tilt & Li Applications and Li application
Describes application modes for Tilt & Lift and Li.
To change to Li application
Procedure to switch the system to Li application mode.
Setting of end limits
Configures the upper and lower travel limits for motors.
Need help?
Do you have a question about the Glydea WT and is the answer not in the manual?
Questions and answers