SOMFY Sonesse 40 RTS Motormanual
Hide thumbs
Also See for Sonesse 40 RTS:
- Manual (64 pages) ,
- Installation instructions manual (60 pages) ,
- Programming instructions manual (21 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for SOMFY Sonesse 40 RTS
Summary of Contents for SOMFY Sonesse 40 RTS
- Page 1 Motor guide Sonesse 40 RTS, 40 WT and 40 I/O ®...
- Page 2 Contents 1. Sonesse® 40 RTS 2. Sonesse® 40 WT 3. Sonesse® 40 I/O...
- Page 3 Sonesse 40 RTS ® Sonesse® 40 RTS is made for interior applications, including roller blinds, and is designed to operate quietly. Technical data Power supply: 230V/50Hz , 120V/60Hz , 220V/60Hz Nominal torque/nominal speed: 1,3Nm/54rpm, 3Nm/30rpm, 6Nm/20rpm, 9Nm/12rpm Frequency: 433,42MHz Operating temperature: 0–60°C Protection rating: IP44 Maximum number of remote controls: 12 Safety advice...
- Page 4 Operating instructions The Sonesse 40 RTS motor can be operated by both a remote control and/or a wall switch. Operating instructions with a remote control Programming DOWN – To move the blind from one level to another, briefly press the UP or DOWN button on the remote.
- Page 5 Replacing a lost remote control Please note that these steps reset/delete all remote controls programmed for the motor. However, upper and lower limits as well as the favourite position are retained. N.B. Only switch off the power supply to the motor synced with the lost remote control.
- Page 6 Readjusting the upper and lower limits (only when the channel is chosen) To readjust the upper limit, press the UP button to move the blind to the current limit. – Hold down the UP and DOWN buttons simultaneously until the blind jogs. –...
- Page 7 Erasing the motor memory Please note that these steps reset/delete all remote controls, upper and lower limits as well as favourite position. N.B. Only switch off the power for the motor to be reset. – Set the blind between the upper and lower limit. –...
- Page 8 Environment Damaged electrical products and batteries should not be disposed of with normal household waste. They should be dropped in specially provided containers or at an authorised organisation that will ensure they are recycled.
- Page 9 Sonesse 40 WT ® Sonesse® 40 WT is made for interior applications, including roller blinds, and is designed to operate quietly. Technical data Power supply: 230V/50Hz, 120V/60Hz, 220V/60Hz, 110V 50/60Hz Nominal torque/nominal speed: 1,3Nm/55rpm, 3Nm/30rpm, 6Nm/20rpm, 9Nm/12rpm Operating temperature: 0–60°C Protection rating: IP 44 Safety advice –...
- Page 10 Operating instructions – To move the blind from one level to another, briefly press the UP or DOWN button on the wired wall switch. – To stop the shade, press the STOP button on the control point. Adjusting the upper and lower limits The upper and lower limits have been pre-set before delivery, but can be adjusted if necessary.
- Page 11 Troubleshooting The motor does not work Check: – The wiring of the motor. – The power supply specifications. – The heat generated (wait for the motor to cool down). The equipment stops too soon Check: – The operation of end-limits during the rotation of the motor. –...
- Page 12 Sonesse 40 I/O ® Sonesse® 40 I/O is made for interior applications, including roller blinds, and is designed to operate quietly. Technical data Power supply: 230V/50Hz Nominal torque/nominal speed: 1,3Nm/50rpm, 3Nm/30rpm, 6Nm/20rpm, 9Nm/12rpm Frequency: 868-870 MHz Operating temperature: 0–60°C Protection rating: IP44 Maximum number of remote controls: 12 Safety advice –...
- Page 13 Operating instructions The Sonesse 40 IO motor can be operated by both a remote control and/or a wall switch. Operating instructions with a remote control: Programming DOWN – To move the blind from one level to another, briefly press the UP or DOWN button on the remote.
- Page 14 – Switch off the power supply for 2 seconds. – Switch the power supply back on for 10 to 15 seconds. – Switch off the power supply for another 2 seconds. – Switch the power supply back on. The blind moves for 5 seconds. If the blind is positioned at an end limit, the movement will only be a jog.
- Page 15 Readjusting the upper and lower limits (only when the channel is chosen) To readjust the upper limit, press the UP button to move the blind to the current limit. – Hold down the UP and DOWN buttons simultaneously until the blind jogs. –...
- Page 16 – Set the blind between the upper and lower limit. – Switch off the power supply for 2 seconds. – Switch the power supply back on for 10 to 15 seconds. – Switch off the power supply for another 2 seconds. –...