Table of Contents
Advertisement
Gelötete Plattenwärmetauscher / Brazed Plate Heat Exchanger /
Achtung:
Lesen Sie diese Anleitung vor Montage und Inbetriebnahme sorgfältig durch. Gewährleistungsansprüche
entfallen, soweit die Montage-, Betriebs- und Wartungsanleitung nicht beachtet wird.
Prüfen Sie bitte bei der Anlieferung, ob Beschädigungen vorhanden sind bzw. ob Teile fehlen. Vermerken
Sie entsprechendes auf den Speditionspapieren.
GEA WTT gelötete Plattenwärmetauscher haben scharfe Kanten. Bitte beachten Sie dieses bei der
Handhabung.
Attention:
Before proceeding with installation and operation please read entire guide carefully. Failure to do so can
cause injury or property damage.
When receiving heat exchangers, any claims for damage or shortage of parts in shipment must be filed
immediately against the transportation company by the consignee.
GEA WTT heat exchangers may have some sharp edges so please handle with care.
Let op:
Lees deze handleiding voor montage en ingebruikneming zorgvuldig door. Aanspraak op garantie komt te
vervallen wanneer de montage-, gebruiks- en onderhoudshandleiding niet in acht is genomen.
Controleer bij aflevering of er beschadigingen aanwezig zijn, resp. of onderdelen ontbreken. Noteer de
desbetreffende constateringen op de transportdocumenten.
Gesoldeerde platenwarmtewisselaars van GEA WTT hebben scherpe randen. Houd daar rekening mee
tijdens handteren.
Bankverbindung: Deutsche Bank AG Frankfurt; BLZ 500 700 10, S.W.I.F.T. Code DEUTDEFF, KTO 0 942 011 00, IBAN DE08 5007 0010 0094 2011 00
Gesoldeerde platenwarmtewisselaars
Montage-, Betriebs- und Wartungsanleitung
Installation and Application Guide
Montage-, gebruiks- en onderhoudshandleiding
Remsaer Straße 2a, 04603 Nobitz - Wilchwitz, Deutschland
Tel. +49 3447 55 39 0, www.gea-phe.com
Jena HRB 202818, ID-No. DE 150 539 388, Steuernr.: 306/5708/5007
GEA WTT GmbH
Geschäftsführung: Andreas Dunkel
Advertisement
Table of Contents
Related Manuals for GEA GBS Series
Summarization of Contents
Safety Warnings
General Danger Warning
Warns about careful reading of the manual and sharp edges on the heat exchanger.
General Attention Warning
Advises careful reading to prevent injury or damage and to check shipments for damage.
General Caution Warning
Stresses careful reading, warranty implications, and handling sharp edges.
Mounting Position and Forces
Mounting Position Guidelines
Provides guidance on optimal mounting orientation for efficient heat transfer and maintenance.
Maximum Fitting Forces and Torques
Details maximum connecting forces and torques for different heat exchanger models.
Piping Connections
Soldering Connection Method
Instructions for cleaning, polishing, fluxing, and soldering the connections to the heat exchanger.
Welding Connection Method
Guidelines for using TIG welding and protecting the heat exchanger from overheating.
Threaded Connection Method
Steps for mounting the heat exchanger and connecting pipes via threaded fittings.
Operation and Anti-freeze
Anti-freeze Protection
Details the use of antifreeze fluids to prevent heat exchanger destruction due to icing.
Fouling and Cleaning
Cleaning Procedures
Procedures for cleaning heat exchangers to remove deposits and prevent damage.
Insulation Options
PUR Hard Foam Insulation
Describes PUR hard foam insulation consisting of two half shells bound by clips.
Diffusion-Resistant Insulation
Describes diffusion-tight insulation made of closed-cell synthetic rubber on NBR basis.
Need help?
Do you have a question about the GBS Series and is the answer not in the manual?
Questions and answers