Table of Contents
Advertisement
3002402/02
INSTALLER GUIDE
C h u r c h i l l
B a l a n c e d F l u e
(GC No. 32-810-58)
ROOM SEALED RADIANT/ CONVECTOR GAS FIRE
(Manufacturer ref. 4733)
THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20)
THIS APPLIANCE IS FOR USE IN THE UNITED KINGDOM (GB) AND THE
REPUBLIC OF IRELAND (IE) ONLY.
INSTALLER: Please leave this guide with the owner
Manufactured exclusively for British Gas & Scottish Gas by Valor Heating
For Service Phone 0845 960 5040
Because our policy is one of constant development and improvement, details may vary
slightly from those given in this publication.
© Valor Heating
Advertisement
Table of Contents
Related Manuals for Valor Churchill
Summarization of Contents
GENERAL INSTALLATION REQUIREMENTS
General Installation Requirements - Walls
Specifies minimum and maximum wall thickness and suitability for combustible cladding.
General Installation Requirements - Timber Frame Building
Details compliance with IGE/UP/7 and seeking local authority advice for timber-framed buildings.
PREPARE THE FIRE
Prepare the Fire - Stand Upright
Instruction to stand the fire upright before proceeding with disassembly.
Prepare the Fire - Detach Case Front
Describes removing the front case by undoing knurled nuts and washers.
Prepare the Fire - Remove Window Unit
Details removing the window unit by detaching wing nuts.
PREPARE THE WALL
Prepare the Wall - Drilling & Flue Hole
Instructions for marking and cutting the flue hole using a template and core drill or chisel.
Prepare the Wall - Core Drilling
Provides guidance on drilling pilot holes and ensuring they are in brickwork, not mortar.
PREPARE FLUE UNIT
Prepare Flue Unit - Measure & Mark Length
Instructions for measuring wall thickness and adding 80mm to determine flue unit length.
Prepare Flue Unit - Cut & Support Tubes
Details cutting the inner and outer flue tubes and removing polystyrene.
TERMINAL GUARD FITTING
Terminal Guard Fitting - Process
Step-by-step guide to folding, positioning, marking, drilling, and refixing the terminal guard.
CHECK IGNITION SPARK
Check Ignition Spark - Verification
Details how to check for a spark between the pilot hood and electrode pin.
Check Ignition Spark - Troubleshooting
Provides steps for checking wire connections and diagnosing pilot unit or gas tap faults.
CONNECT TO THE GAS SUPPLY
Connect to Gas Supply - Connection
Describes connecting the gas supply pipe to the appliance inlet using an isolating elbow.
Connect to Gas Supply - Isolation & Testing
Emphasizes provision for isolation and pressure testing the installation for gas soundness.
FITTING COALS
Fitting Coals - Place Fuel Bed
Instruction for placing the fuel bed base correctly under the locating strip.
Fitting Coals - Position Front Coals
Guides on placing the front right and front left coals on the metal ledge.
CHECK APPLIANCE OPERATION
Check Appliance Operation - Gas & Pilot
Steps for checking gas joints, operating the control knob for pilot ignition, and purging air.
Check Appliance Operation - Burner Flames
Guides on checking main and decorative burner ignition at low and max settings.
REPLACE OUTER CASE
Replace Outer Case - Lower & Secure
Instructions for positioning and securing the outer case using knurled nuts.
MAKE FINAL CHECKS AND INSTRUCT USER
Final Checks & User Instruction - Operation
Rechecking pilot, operation through settings, and advising on initial odour.
Final Checks & User Instruction - Advice
Advises on metal discoloration, broken glass panel, and annual servicing by competent persons.
SERVICING
Servicing - Remove Outer Case
Steps for removing the outer case for servicing purposes.
Servicing - Remove Window Unit
Steps for removing the window unit during servicing.
Servicing - Remove Ceramic Fuel Items
Instructions for removing coals and coal bed during servicing.
Servicing - Remove Burner(s)
Steps for removing the main and decorative flame burners.
Need help?
Do you have a question about the Churchill and is the answer not in the manual?
Questions and answers