Table of Contents
Advertisement
CONFORMS TO UL STD 325
UL CLASS - I, II, III, IV
CERTIFIED TO CAN/CSA STD
C22.2 NO. 247
H
P
i g
r
h
o
f
1 4
i l
e
0
2
2
0
2
2
H
0
0
P
0
0
H
H
P
P
P
L
U
S
Version 10
Residential / Commercial
Brushless DC
Swing Gate Operators
Made in USA
www.max.us.com
Quick Install Guide for
Mega tron
Swing Gate Operator
SAFETY SENSORS REQUIRED
0
0
0
S
1 4
0
L U
2
2
P
T
0
S
S
0
L U
2
F A
2
P
T
S
F A
4009963
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Max Megatron 2200
Summarization of Contents
Operator Placement Guidelines
Placement Calculations
Key measurements for operator placement, including gate length and clearance.
Arm Placement Restrictions
Rules regarding arm length and positioning relative to the gate.
Arm Position Adjustment
Open and Closed Position Guidelines
Correct arm positions for open and closed gates, including gap requirements.
Re-attaching the Arm
Procedure for securely re-attaching the gate arm to the operator.
Release Handle Clamp Setup
Clamp Adjustment and Testing
Steps for adjusting the clamp and testing for slippage.
Re-attaching Arm to Operator
Specific instructions for re-connecting the arm to the release handle clamp.
AC Input Power Connection
Input Power Options and Setup
Selecting between 115VAC and 230VAC power input.
Powering On and Off Procedures
Safe steps for turning the operator's power on and off.
Grounding and Direction Setup
Operator Grounding Requirements
Importance and methods for grounding the gate operator for safety.
Setting Opening Direction and ID Plug
Configuring gate opening direction and installing the ID plug.
Limit Switch Adjustment
Adjusting Limit Switches
Procedure for setting the gate's open and closed limit positions.
Fine-Tuning Limit Rings
Advanced adjustment for the limit rings for precise gate control.
Entrapment Protection Wiring
Typical Wiring Configurations
Wiring examples for photocells and other safety sensors.
Device Location Considerations
Guidance on where to install entrapment protection devices for optimal safety.
Entrapment Protection Options
Top View Layouts
Diagrams showing sensor placement from a top-down perspective.
Side View Layouts
Diagrams illustrating sensor placement from a side view.
Learn Gate Positions
Gate Position Learning Procedure
Steps to teach the operator the gate's fully open and closed positions.
ERD Sensor and Loop Detectors
ERD Sensor Adjustment Guide
How to adjust the ERD sensor sensitivity for proper operation.
Loop Detector Connections and Setup
Wiring and configuration for various loop detector types.
Matrix 1 Settings Configuration
Key Matrix 1 Setting Options
Configuration of features like Battery Back-Up, Close Timer, and Gate Speed.
Wiring Opening Device Options
Connecting external devices like maglocks and keypads to the operator.
Dual Gate Operator Wiring
Primary and Secondary Operator Setup
Connecting and configuring primary and secondary gate operators.
General Troubleshooting
Using the USB Black Box Port
Procedure for downloading error logs and event history.
Testing Entrapment Sensors
Steps to test the Edge 1 entrapment protection sensor.
Gate Cycling Troubleshooting
Common Gate Operational Symptoms
Troubleshooting guide based on observed gate symptoms and potential causes.
Matrix 1 LED Diagnostics
Matrix 1 LED Status Indicators
Interpreting LED lights on the Matrix 1 board for troubleshooting.
Matrix 1 LED Continued Diagnostics
Additional Matrix 1 LED Statuses
Further LED interpretations for Photocell, Motor Overload, and Loop status.
MC-200 LED Troubleshooting
MC-200 LED Status and Solutions
Diagnosing MC-200 issues using LED indicators and their solutions.
BC-7 Module LED Troubleshooting
BC-7 Module LED Indicators
Troubleshooting the battery module using its LED status lights.
Safety Sensor Wiring Guides
OMRON Photocell Wiring
Installation guide for OMRON E3K-RIOK4 photocell sensors.
EMX IRB-RET Photocell Wiring
Installation guide for EMX IRB-RET photocell sensors.
EMX IRB-MON Photocell Wiring
Transmitter (TX) Installation Steps
Steps for installing and configuring the EMX IRB-MON transmitter.
Receiver (RX) Installation Steps
Steps for installing and configuring the EMX IRB-MON receiver.
Dual Gate Photocell Wiring
EMX IRB-MON Dual Gate Setup
Wiring and configuration for EMX IRB-MON photocells in dual gate systems.
Miller Gate Link Wireless Communication
Gate Link Receiver/Transmitter Programming
Procedure for programming the Miller Gate Link wireless system.
Need help?
Do you have a question about the Megatron 2200 and is the answer not in the manual?
Questions and answers