Denon AVR-3310CI Owner's Manual page 14

ENGLISH
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Setting items
Surround Parameters
(Continued)
• This can also be set by pressing STANDARD.
• If the source being played contains a surround back signal, the decoder
type is automatically selected by the AFDM function. Set "AFDM" to
"OFF" to switch to your preferred decoder.
• If the setting in "Speaker Configuration" – "Surround Back" (vpage 9)
is "None", "Surround Back" is not displayed.
Subwoofer Att. : Attenuate subwoofer level when using EXT. IN input.
• ON : Set.
• OFF : Do not set. Usually use in this mode.
S et this to "ON" if the subwoofer channel level seems too high when
playing audio signal.
Subwoofer : Turn subwoofer output on and off.
• ON : The subwoofer is used.
• OFF : The subwoofer is not used.
Default : Restores all the surround parameter settings to their defaults.
• No : Do not reset to the defaults.
• Yes : Reset to the defaults.
Tone
Tone Control : Sets the tone control function ON and OFF.
• ON : Allow tone adjustment (treble, bass).
Adjust the tonal quality of
• OFF : Playback without tone adjustment.
the sound.
• This can be set when "Dynamic EQ" (vpage 14) is set to "OFF".
• The tone cannot be adjusted in the direct mode.
Bass : Adjust low frequency range (bass).
• –6dB ~ +6dB
This can be set when "Tone Control" (vpage 13) is set to "ON".
Treble : Adjust high frequency range (treble).
• –6dB ~ +6dB
This can be set when "Tone Control" (vpage 13) is set to "ON".

Main remote control
operation buttons
Setting contents
:Displaying the menu :Moves the cursor
Cancel the menu (Up/Down/Left/Right)
Setting items
Audyssey Settings MultEQ : Corrects both time and frequency response problems in the
Set Audyssey MultEQ ® ,
listening area.
Audyssey Dynamic EQ ®
•
Audyssey : Optimize the frequency response of all speakers.
• A udyssey Byp.L/R : Optimize frequency response of speakers except
and Audyssey Dynamic
front L and R speakers.
Volume™.
• A udyssey Flat : Optimize frequency response of all speakers to flat
NOTE
response.
• M anual : Apply frequency response set with "Manual EQ" (vpage
I f you have not performed
16).
Auto Setup, or if you
• OFF : Turn "MultEQ" equalizer off.
change the speaker
settings after performing
Auto Setup, you may not
• " Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be
be able to select Dynamic
selected after Audyssey Auto Setup has been performed. "Audyssey"
EQ/Dynamic Volume, and
is automatically selected after performing Audyssey Auto Setup. "When
"Run Audyssey" may be
"Audyssey", " Audyssey B yp. L /R" o r " Audyssey F lat" i s s elected, "
displayed.
lights.
In this case, either perform
• A fter running Audyssey Auto Setup, if the Speaker Configuration,
Audyssey Auto Setup over
Distance, Channel Level, and Crossover Frequency have changed without
again or perform "Restore"
increasing the number of speakers measured, only "
(vpage 33 of GThe
• If "Dynamic EQ" or "Dynamic Volume" is set to "ON" when "MultEQ"
original versionH Operating
is set to either "OFF" or "Manual", "MultEQ" is automatically set to
Instructions) to return to
"Audyssey".
the settings after Audyssey
• You can also press
Auto Setup was run.
NOTE
• " MultEQ" and "Manual EQ" cannot be selected when "EQ Customize"
is set to "Not Used" (vpage 38 of GThe original versionH Operating
Instructions).
• W hen using headphones, "MultEQ" is set to "OFF".
:Confirm the setting
Setting contents
" lights.
MULTEQ
to set.
:Return to previous menu
"