System Exclusive Device Channel / Midi Merge; Program Dump - DigiTech STUDIO QUAD V2 User Manual

Studio Quad V2 User's Manual
Program
change number to recall. As this number increases above Program 100, note that STUDIOUSER changes to
STUDIOFACT, indicating that the mapped number will recall the indicated Program number in the Factory
bank. Pressing <3> again will toggle between the User and Factory banks.
• Scrolling one notch above STUDIOFACT pgm180 (or one notch below STUDIOUSER pgm100) selects
STUDIO BYP which allows you to bypass the Studio Quad V2 by sending it the selected MIDI program
change number.
• When you're finished, you can return to Program mode by pressing <PROGRAM>.

SYSTEM EXCLUSIVE DEVICE CHANNEL / MIDI MERGE

An easy way to think of the System Exclusive Device Channel option is to separate System Exclusive data from nor-
mal MIDI data. Each type of data has its own group of 16 channels upon which data can be transmitted. Normal
MIDI data, like Program Changes, MIDI Volume, Modulation, etc. is transmitted and received on the MIDI channel
designated by the setting of MIDI CHANNEL (see pg. 31). SysEx data, on the other hand, is transmitted and received
on the SysEx channel designated by the setting of SYSEX DEVICE CHANNEL.This setup frees up your regular MIDI
channels for other control options, and gives you the flexibility to request SysEx data from only the devices you
want in your setup, whether they share the same MIDI channel or not.
The MIDI merging option allows incoming MIDI data to be merged with any MIDI data generated by the
Studio Quad V2 before being sent to the MIDI Out port.
To change the SysEx Device Channel number or MIDI Merge setting, do the following:
• Press <UTILITY>, and scroll to Page 3 of the Utility Menu using the <NEXT PAGE> and <PREVIOUS PAGE>
keys. The display reads:
• Use the <2> and <4> buttons, and the Data wheel to select the desired SysEx channel (1, 2,...15, 16), or set
the MIDI merge to ON/OFF.
• When you're finished, you can return to Program mode by pressing <PROGRAM>.

PROGRAM DUMP

Allows you to dump individual Studio Quad V2 Programs to another Studio Quad V2 or external MIDI devices like
patch librarians, computers, or sequencers for backup, storage, or organization. This option allows you to select the
Program to be dumped, and (when dumping to another Studio Quad V2) the Program location where you want the
Program dumped.
To initiate an individual patch dump from the Studio Quad V2, do the following:
• Press <UTILITY> and scroll to Page 4 of the Utility Menu using the <NEXT PAGE> and <PREV PAGE> keys.
The display reads:
1
SysEx DevChnl MIDI Merge
C C C C
1
%kHz %kHz
1 2
m Sec m Sec
CHANGED
MIDI
CLIP
LEVEL 1
FACTORY PRG - CHANGED
S-DISC ™
CLIP
P
- CHANGED ROCESSING
LEVEL 2
CLIP
UTILITY PAGE
LEVEL 3
1 2 3 4 5 6 7 8 9 10 CLIP
LEVEL 4
1
DumpFact as Prg-press[4]
C C C C
888 1
%kHz %kHz
1 2
m Sec m Sec
CHANGED
MIDI
CLIP
LEVEL 1
FACTORY PRG - CHANGED
S-DISC ™
CLIP
P
USER PRG - CHANGED ROCESSING
LEVEL 2
CLIP
FX EDIT PAGE UTILITY PAGE
LEVEL 3
1 2 3 4 5 6 7 8 9 10
CLIP
LEVEL 4
C C
Off
% %
3
4
m Sec
CHANGED CHANGED
IN 1 OUT 1
IN 2 OUT 2
IN 3 OUT 3
IN 4 OUT 4
DIGITAL CLIP MODIFIERS
C C C C
1 Yes
%kHz %kHz
3 4
m Sec m Sec
CHANGED
IN 1 OUT 1
IN 2 OUT 2
IN 3 OUT 3
IN 4 OUT 4
DIGITAL CLIP MODIFIERS
Section 4 - In Levels and Utilities
31