Forging Mount HY9390-B Instruction Manual

www.forgingmount.com
Instruction Manual
FULL MOTION
TV WALL MOUNT
±90°
Model: HY9390-B ±90°
VESA:600X400mm (Max)
Tape Electric 1/2 in (13 mm)
Measure Pencil Screwdriver Drill Socket Wrench
7/32in.
(5mm)
Wood
Stud Finder Awl Drill Bit Hammer
Step 1-1 Select TV Screw Diameter Step 1-2 Select TV Screw Length
Hand thread screws into the threaded inserts
If your TV has a flat back, AND you want your TV closer
on the back of your TV to determine which
to the wall, use the shorter screws(A).
screw diameter ( M4, M6, or M8 ) to use.
Use the spacers and longer screws(B) to accommodate:
M4 M6 M8
Does your TV (including accessories)
weigth more than 110 lbs. ( 50 kg )?
V2.0
No — Perfect!
Yes— This mount is NOT compatible.
±90°
+5°
-12°
capacity can result in serious personal
injury or damage to equipment! It is the
installers's responsibility to make sure the
weight of the TV (with accessories) does
not exceed 110 lbs(50kg).
Arm Assembly/ Wall Plate
WARNING :
This product
contains small items that could
be a choking hazard if swallowed.
Before starting assembly, verify
all parts are included and
undamaged. If any parts are
missing or damaged, do not return
TV Bracket
the damaged item to your dealer;
contact with Customer Service.
3/8in. Never use damaged parts!
(10mm)
NOTE: Not all parts and hardware
Concrete
Drill Bit
included will be used.
· Round/irregular back TVs
· TVs with inset mounting holes
· Extra space needed for cables
FLAT BACK ROUND BACK INSET HOLES CABLES
What is your wall made of ?
110 lbs
Perfect!
(50kg)
Solid concrete or
Exceeding the weight
concrete block?
Front Support Arm Extension
01 02 03
x1 x1 x4
Wall Plate Template Level Velcro Tie
Drilling Template
UP
04 05 06 07
x2 x1 x1 x5
Step 1-3 Secure the Connection Plate / TV Brackets to the back of TV
Standard configurations
Position your Connection Plate / TV brackets over your
are shown. For special
TV hole pattern- making sure the brackets are centered
applications, or if you
and level over the TV hole pattern.Secure the TV plate
are uncertain about your
or brackets using your screw/washer spacer selectiion:
hardware selection,
(a) for Flat Back
you can contact at:
(b) for Round Back/Extra space
forgingmount888@163.com
CAUTION: Ensure TV mount plate / bracket is
securely fastened before moving on to the next step.
CAUTION:
Verify
(a1) Flat Back
adequate thread engagement
with the screw/washer/spacer
combination and TV bracket. D
-Too short will not hold the TV.
J-1
-Too long will damage the TV.
Too Short
(b1) Round Back / Extra Space
Correct
E
J-1
Too Long
K/L/T
Please read through these instructions completely to be sure you're comfortable with
this install process. Also check your TV owner's manual to see if there are any special
Dry wall with
requirements for mounting your TV.
woodstuds ?
If you do not understand these instructions or have doubts about the safety of the installation,
assembly or use of this product, please contact US via: forgingmount888@163.com
CAUTION:
Avoid potential personal injuries and property damage!
This product is designed for use in wood stud/concrete walls DO NOT install into drywall.
The wall must be capable of supportingfive times the weight of the TV and mount combined.
Do not use this product for any purpose not explicitly specified by manufacturer.
WARNING
Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
Lag Bolt Lag Bolt
TV Screws
Washers
5/16x2.75"
M4X12mm M4X30mm
A
B
x4
x4
D
E
x4 x4
Wall Anchor
C
x4
M6X15mm M6X35mm
F G
WARNING x4 x4
:
Installation must use the
screws and accessories
provided by our company,
otherwise we are not
M8X15mm M8X30mm
responsible for any
H I
x4 x4
problems.
If your TV VESA is less than 100x200,
you need to loosen the four pre-assembled
S1
bolts , remove the arm extension
from the Front Support
use the connection plate of the
Front Support to install the TV.
(a2) Flat Back
F
(b2) Round Back / Extra Space
G
Alternate Spacer Setups
K/L/T
TV Washers Securement Screws Allen key
Ø5 Ø8 M5X12mm Ø5
J-1 J-2 M N O
x4 x4 x2 x2
TV Spacers Wrench
L2.5MM L10MM L22MM
M8X50mm
K L T P
X
x8 x4 x4
x4
100
02
O
02
, and then
S1
04
D/F/H
J-1/J-2
04
E/G/I/X
J-1/J-2
Alternate Spacer Setups
K/L/T
x1
x1