Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NI sbRIO-9687
Summary of Contents for NI sbRIO-9687
- Page 1 Getting Started 2024-04-26...
-
Page 2: Table Of Contents
Powering on the sbRIO-9687........ -
Page 3: Overview
Getting Started Overview This document describes how to install and begin using the sbRIO-9687 GPIC Universal Interface Board. © 2017 National Instruments Corporation. All rights reserved. Refer to the <National Instruments>\_Legal Information directory for information about NI copyright, patents, trademarks, warranties, product warnings, and export compliance. -
Page 4: Unpacking The Kit
Getting Started Caution Use the sbRIO-9687 with only sbRIO-9683 or sbRIO-9684 devices. The sbRIO-9687 is not electrically or mechanically compatible with other NI devices. Caution The sbRIO-9683 or sbRIO-9684 simultaneous sampled isolated AI's common ground is short circuited to the main ground on the sbRIO-9687 interface board when assembled, defeating the channel-to- common isolation ratings of these circuits. - Page 5 (QTY 4) Standoffs and screws, sbRIO to RMC, M3 × 9.65 mm M-F, 4.5 mm Hex, ■ M3 × 5 mm panhead screws sbRIO power cable assembly, mini-fit pigtail, 2C, 12 in. ■ NI 9683 User Manual and Specifications or NI 9684 User Manual and ■ Specifications sbRIO Thermal Kit: ■...
-
Page 6: Hardware Overview
Thermal Kit for NI sbRIO-9607/9627/9637 Installation and ■ Specifications Manual Hardware Overview The sbRIO-9687 is intended to be used together with the sbRIO-9683 or sbRIO-9684 General Purpose Inverter Controller and the sbRIO-9607 CompactRIO Single-Board Controller. These boards are designed to be stacked with board-to-board connectors. -
Page 7: Dimensions
14. Relay outputs 15. Feedback connectors 16. DO breakout connector Dimensions The following figures show the board dimensions and connector height for the sbRIO-9687. For detailed dimensional drawings and 3D models, visit ni.com/ dimensions and search for 9687. © National Instruments... -
Page 8: Power
Getting Started Figure 2. Primary Side Dimensions, Millimeters (Inches) 4X Ø 4.37 mm (0.172 in.) Figure 3. Height of Expansion Board Connectors, Millimeters (Inches) Power Input voltage (+24 V) Typical +24 V Maximum +28.8 V Minimum +19.2 V Maximum DC input current F4 Fuse 10 A, 250 VAC, Fast Acting, .25 in. -
Page 9: Preparing The Environment
Getting Started Preparing the Environment Ensure that the environment in which you are using the sbRIO-9687 meets the following specifications. -40 °C to 85 °C Operating temperature (IEC 60068-2-1, IEC 60068-2-2) Storage temperature (IEC 60068-2-1, IEC -40 °C to 85 °C... -
Page 10: Installing The Thermal Kit And The Sbrio-9607
Getting Started Note Eight M3 nuts are included with sbRIO-9684 mounting hardware. These M3 nuts are provided to secure the board assembly for temporary mounting configurations where holes are not tapped into the mounting surface. To prevent possible damage to the device, use caution when installing the M3 nuts. -
Page 11: Mounting The Sbrio-9683 Or Sbrio-9684
Attach a data cable to the sbRIO-9607 CAN connector. c. Attach the power cable to the sbRIO-9607 power connector. 4. Apply the gap pad to the sbRIO-9607. Refer to the Thermal Kit for NI sbRIO-9607/9627/9637 Installation and Specifications Manual for information about gap pad placement. - Page 12 Getting Started 1. Install the M3 × 29.81 mm, M-F standoffs to the tapped holes for the sbRIO-9683 or sbRIO-9684 . 2. Align the sbRIO-9683 or sbRIO-9684 with the M3 × 29.81 mm, M-F standoffs and the sbRIO-9607. 3. Seat the mezzanine card connectors on the sbRIO-9683 or sbRIO-9684 and the sbRIO-9607 to connect the boards.
-
Page 13: Mounting The Sbrio-9687
Figure 6. Mating the sbRIO-9683 or sbRIO-9684 to the sbRIO-9607 Mounting the sbRIO-9687 1. Install the sbRIO-9687 handles. a. Align the handles with the dedicated fixing holes on the sbRIO-9687. b. Insert two 8-32 × 3/8 in. panhead screws for each handle through the sbRIO-9687. - Page 14 Getting Started b. Align the sbRIO-9687 with the M3 x 43.36, M-F standoffs and the four M3 x 11.12, M-F standoffs. c. Seat the sbRIO-9687 connectors and the sbRIO-9683 or sbRIO-9684 connectors to connect the boards. d. Insert and tighten M3 x 5 panhead screws through the sbRIO-9687 to the installed M3 x 43.36, M-F standoffs and to the M3 x 11.12, M-F standoffs.
- Page 15 Getting Started Figure 7. Mating the sbRIO-9687 to the sbRIO-9683 or sbRIO-9684 The following figure shows the completed assembly of the sbRIO-9607 controller, sbRIO-9683 or sbRIO-9684 mezzanine board, and the sbRIO-9687 GPIC universal interface board. © National Instruments...
-
Page 16: Surface Mounting Dimensions
Getting Started Figure 8. Complete Assembly Surface Mounting Dimensions The following figures depict the mounting dimensions for the sbRIO-9687. Figure 9. Mounting Plate, Inches (Millimeters) 16.97 in (430.91 mm) 4X Ø .250 in (6.35 mm) 8.0 in 11.0 in (203.2 mm) -
Page 17: Connecting The Sbrio-9687
5mm minimum thread depth Connecting the sbRIO-9687 The top side of the PCB is the primary side of the sbRIO-9687 and contains connectors for inverter modules, simultaneous AI, scanned AI and AO, feedback inputs, digital inputs, digital outputs, relay outputs, display interface, expansion board, and power. -
Page 18: Powering On The Sbrio-9687
3. Turn on the power supply. Powering on the sbRIO-9687 The sbRIO-9687 turns ON immediately after the input power is present. One green LED is always ON when power is present. The sbRIO-9607 is powered through sbRIO-9687. The sbRIO-9607 runs a power-on self test (POST) when it is powered on. -
Page 19: Troubleshooting
Troubleshooting When the sbRIO-9687 is operating, the onboard power LED is ON. If the power LED is OFF, check if the input power is present and has the correct polarity. The following figure shows the LEDs on the sbRIO-9687. -
Page 20: Related Documentation
For additional information, refer to the following documents. sbRIO-9687 Specifications ■ sbRIO-9687 User Manual ■ NI sbRIO-9607 Getting Started Guide ■ Thermal Kit for NI sbRIO-9607/9627/9637 Installation and ■ Specifications Manual NI sbRIO-9607/9627 RIO Mezzanine Card Design Guide ■ NI 9683 User Manual and Specifications ■... - Page 21 NI product. Product registration facilitates technical support and ensures that you receive important information updates from NI corporate headquarters is located at 11500 N Mopac Expwy, Austin, TX, 78759-3504, USA. © National Instruments © 2024 National Instruments Corporation.
Need help?
Do you have a question about the sbRIO-9687 and is the answer not in the manual?
Questions and answers