Download Print this page

Seima Chios Vortex Flush Wall Faced Installation Manual

Toilet suite

Advertisement

Quick Links

Installation Guide
Chios Vortex Flush Wall Faced Toilet Suite
Cistern package contents
1 x ceramic cistern lid
2 x bolts w seals
1 x ceramic cistern base
For attaching
Cistern is supplied with
cistern to pan.
flush valve and connector
pipe already installed.
Pan package contents
1 x ceramic pan
seima.com.au
Important !
1
Inspect the components before installation to ensure there are no visible defects. If a defect
is found, do not install the toilet suite and contact the supplier immediately. Claims for
defects will not be accepted after the product has been installed.
2
This toilet suite is suitable for a variety of setups:
Cistern – Accommodates either Back Entry Inlet or Bottom Entry Inlet (left or right).
Pan – Universal – Accommodates S-trap or P-trap installation (P-trap connector not supplied).
3
Must be installed by a licensed plumber in accordance with Australian Standard AS3500 and
meet the requirements of local licensing authorities. Failure to do so may void the warranty.
2 x plugs
1 x rubber seal
Plugs can be
For sealing outlet at
used to plug
base of cistern
holes in sides of
pan if required.
Threaded
Large end of pan connector can
section can
be trimmed to suit setout.
be trimmed to
required size.
1 x pan connector
For connecting pan to
floor outlet pipe/S‑trap.
1 x threaded section (with
flange plate)
Flange attaches to wall;
threaded section links to
pan connector.
Please note
− Installation shall be in accordance with AS/NZS3500.
− All measurements are in millimetres. Height dimensions are to
base of pan. Make allowance for bedding.
− Bedding: Pan may be bedded with cement base or using
silicone sealant. Fix pan to floor using a sand cement mixture of
3:1 to a depth of 60mm. Do not use lime or fast-drying cement.
− Bracket fixing: The pan should be bedded with silicone sealant
and fixed with the brackets supplied.
1 x flush button
Half flush left, full
flush right.
2 x concealed
2 x floor bolts
fixing brackets
(and white plugs)
2 x washers
Optional — can
be used to
Optional fixing #2
connect pan to
— used with fixing
floor.
brackets to secure
pan to floor. Bolt
is inserted through
bracket base hole.
1 x flexible hose
1 x bottom entry
with bend
inlet connector
Pre‑installed
pipe
inside cistern,
Pre‑installed
comes attached
inside cistern. Use
to Inlet Valve.
for bottom entry
installations only;
to be left in cistern
if not used.
2 x caps
2 x screws
2 x pan plugs
Optional fixing #2 — used to
secure pan to concealed fixing
bracket. Plastic plug is placed
into hole in side of pan exterior,
screw is rebated into plug
and then screws into a hole
in upright section of bracket.
Chrome cap is used to cover
plastic plug.
− Do NOT use epoxy type adhesives.
− Dimensions are nominal and subject to normal
ceramic manufacturing variations.
− Specifications may vary without notice as part of
our continuous improvement practices.
− Clean with a damp cloth. Do not use abrasive
cleaners, liquids or pastes.
chios-vtx-wf-in | v 2.0 | 05-25 | page 1 of 4

Advertisement

loading
Need help?

Need help?

Do you have a question about the Chios Vortex Flush Wall Faced and is the answer not in the manual?

Questions and answers

Summary of Contents for Seima Chios Vortex Flush Wall Faced

  • Page 1 Installation Guide Chios Vortex Flush Wall Faced Toilet Suite Important ! Inspect the components before installation to ensure there are no visible defects. If a defect is found, do not install the toilet suite and contact the supplier immediately. Claims for defects will not be accepted after the product has been installed.
  • Page 2 Installation Guide Chios Vortex Flush Wall Faced Toilet Suite Diagram A — Cistern setup when supplied Inlet Valve and Flexible Hose Click Inlet Valve into place Back Entry Flush Valve onto Flush Valve. Inlet Nozzle Inlet Inlet Valve Valve locates onto...
  • Page 3 4 Back Entry installation 6 Securing the pan on the floor (see Diagram B) Connect the flexible hose to the ½” BSP nipple in the wall outlet. Cement fixing (Optional fixing #1) Run the flexible hose behind the flush valve, ensuring that the If using cement bedding, level the pan while the cement hose does not obstruct the operation of the flush valve.
  • Page 4 10 Seat package contents 1 x seat and lid 2 x stainless steel caps Has receptor holes that slide (used to cover stainless steel plate w pin) onto stainless steel pins. 2 x stainless steel plates with pin (seat locates onto stainless steel pins) 2 x metal bolts (used for securing stainless steel plate and pin to pan)