Advertisement
Quick Links
CONVENTIONAL WALL SOUNDER + VISUAL ALARM DEVICE
CONVENTIONAL WALL SOUNDER + VISUAL ALARM DEVICE
OVERVIEW
This add-in interface module permits the use of the CWS100, CWS100(W), CWS100-AV and CWS100-AV(W) conventional sounders on an
Altair intelligent loop.
COMPATIBILITY
This module is compatible only with:
- Intelligent control panels and systems based on the Argus Security Altair protocol.
- the conventional CWS100, CWS100(W) sounder and CWS100-AV, CWS100-AV(W) sounder/VAD.
For more specific information regarding compatibility refer to your fire security system supplier and the technical documentation concerning the
control panel in use.
The VdS approvals for products CWS100, CWS100(W), CWS100-AV, CWS100-AV(W) is only valid in combination with the
ALWS-MOD module. The ALWS-MOD is mentioned in the appendix of the respective approvals. If the sirens are combined
with another module, the VdS approvals expires. The devices are only VdS approved to Type A (indoor application).
INSTALLATION - IMPORTANT NOTES
This module must be wired according to the wiring details described in this manual.
Disconnect the intelligent loop from the control panel before wiring.
Test the ALWS-MOD and CWS100, CWS100(W) / CWS100-AV, CWS100-AV(W) assembly after installation.
ASSOCIATED DEVICE'S INSTALLATION INSTRUCTIONS
This manual provides installation instructions limited only to the ALWS-MOD.
For specific installation instructions about the CWS100, CWS100(W), CWS100-AV and CWS100-AV(W) refer to their separate manuals:
CWS100, CWS100(W) installation instructions
CWS100-AV, CWS100-AV(W) installation instructions
BEFORE ADDING IN THE MODULE
As described in the CWS100, CWS100(W) / CWS100-AV, CWS100-AV(W) manuals remember to:
1) Detach the front sounder body from the sounder back box.
2) Prepare the cable entry (or entries) on the sounder back box.
3) Fix the sounder back box to the wall.
4) Assign a loop address to this module (as described below).
ADDRESS ASSIGNMENT
An address must be assigned to the device:
- The address must be unique: no other device on the intelligent loop must have the same address.
- It is possible to select an address between 1 and 240.
In order to address the module, use one of the following methods:
- Use the ALPU1000 manual programmer: this must be connected to the intelligent interface module using a suitable connector; for further
information consult the manual programmer's instructions and refer to the following "CONNECTION TO THE ALPU1000 MANUAL
PROGRAMMER" section.
- Perform the automatic addressing routine from the control panel once all loop devices have been wired.
This method can be used only if the control panel has been designed with this functionality; in any case, refer to your control panel manual
and, above all, your system supplier, since performing this process is not possible on all types of installations.
For identification purposes, it is possible to record the loop number and device address on the module label.
ARGUS SECURITY S.R.L. - Via del Canneto, 14 - 34015 - Muggia (TS) - Italy
ALWS-MOD +
ALTAIR WALL SOUNDER MODULE
CWS100 *
CONVENTIONAL WALL SOUNDER
CWS100(W) *
CONVENTIONAL WALL SOUNDER
CWS100-AV **
CWS100-AV(W) **
code: L20-CWSXX-0001, L20-CWSWX-0001
code: L20-CWSVX-0001, L20-CWSVW-0001
928ah/01
*
**
928z/01
G225023*
G225024**
www.argussecurity.it
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Argus Security CWS100W Series
Summary of Contents for Argus Security CWS100W Series
- Page 1 For identification purposes, it is possible to record the loop number and device address on the module label. ARGUS SECURITY S.R.L. - Via del Canneto, 14 - 34015 - Muggia (TS) - Italy www.argussecurity.it...
- Page 2 CONNECTION TO THE ALPU1000 MANUAL PROGRAMMER Unscrew and detach the terminal block from the jack connection cable (supplied with the ALPU1000). Insert and SECURE using screw terminals: - The BLACK wire into the Loop in (-) terminal block. - The RED wire into the Loop in (+) terminal block. The sounder module must not be connected to the loop or to other devices when using the programmer.
- Page 3 Connection for the intelligent loop’s output positive (+) cable. Table 1 Intelligent loop (+) Loop out (+) Loop in (+) Loop out (-) Loop in (-) Intelligent loop (-) Picture 4 ARGUS SECURITY S.R.L. - Via del Canneto, 14 - 34015 - Muggia (TS) - Italy www.argussecurity.it...
- Page 4 CO5310UK ** CO5310CPR ** and the fire location and may be affected by special environmental conditions. Refer to and follow national codes of practice and other internationally recognized fire engineering ARGUS SECURITY S.R.L. standards. Via del Canneto, 14 34015 Muggia (TS)
Need help?
Do you have a question about the CWS100W Series and is the answer not in the manual?
Questions and answers