Download Print this page

Advertisement

Quick Links

INSTALLATION MANUAL
Level of Difficulty
Difficult
Installation difficulty levels are based on time
and effort involved and may vary depending on
the installer level of expertise, condition of the
vehicle and proper tools and equipment.
Installed Attachment Tabs
Height
13-1/2"
Width
18"
Parts List
Item Qty Description
1
1
Tow bar base plate
2
2
Tow bar mounting tab
3
2
Safety cable, 3,500 lbs.
4
8
Carriage bolt,
3/8"-16 x 1-1/2", grade 8
5
8
Square hole spacer,
1/4" x 1" x 2"
6
8
Flange nut, 3/8"-16, grade 8
7
2
Quick link, 1/4"
8
2
Socket plug
Tools Required
Torque wrench
Drill
Socket, 9/16"
Drill bit, 1/4"
Socket, 10mm
Drill bit, 13/32"
Socket, 13mm
T20 Torx
Reciprocating saw
Tape measure
Large vise grip
Phillips screwdriver
Utility knife
Flat head screwdriver
Fishwire, 3/8"
--
(includes eight)
CURTMFG.COM
PRODUCT SUPPORT: 877.287.8634
WARNING
Never exceed the vehicle manufacturer's recommended gross vehicle weight rating (GVWR).
Product Photo
Not pictured: Safety cables, quick links and socket plugs
CAUTION
Take care when cutting any plastic or metal as injury may occur if done improperly.
NOTICE
Visit www.curtmfg.com for a full-color copy of this
instruction manual, as well as helpful videos, guides and much more!
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
This installation requires front fascia panels, supports and a portion of the underbody panel
to be temporarily removed and reinstalled. Some drilling and trimming are required.
To help prevent damage to the product or vehicle, refer to the specified
torque specifications when securing hardware during the installation process.
If equipped, we recommend removing the base plate attachment tabs when not in use.
SAFETY INSTRUCTIONS
Safety glasses should be worn at all times while installing this product.
Product Registration and Warranty
CURT stands behind our products with industry-leading warranties. To get copies of the product
warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys
70116-INS-RC
04/14/2020
ECN6926
PAGE 1
70116

Advertisement

loading
Need help?

Need help?

Do you have a question about the 70116 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for curt 70116

  • Page 1 Safety glasses should be worn at all times while installing this product. Product Registration and Warranty CURT stands behind our products with industry-leading warranties. To get copies of the product warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys CURTMFG.COM •...
  • Page 2 Carriage bolt, 3/8"-16 x 1-1/2", grade 8 Square hole spacer, 1/4" x 1" x 2" Flange nut, 3/8"-16, grade 8 Quick link, 1/4" Socket plug Included fishwire CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70116-INS-RC • 04/14/2020 • ECN6926 • PAGE 2...
  • Page 3: Bumper Removal

    Repeat on the other side of the vehicle. Step 3 Use a T20 Torx bit to remove the seven bolts holding the underbody fascia, three on either side and one in the center. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70116-INS-RC • 04/14/2020 • ECN6926 • PAGE 3...
  • Page 4 Remove the bumper fascia by pulling up and out at the edges, near the wheel wells. Make sure to disconnect any electrical harnesses. Then, remove the bumper fascia entirely and set it aside. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70116-INS-RC • 04/14/2020 • ECN6926 • PAGE 4...
  • Page 5 As shown, mark a notch in the bumper about 2" from the edge. Then, use a metal-cutting tool (reciprocating saw or cutoff wheel) to cut off the marked area. Repeat on the other side. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70116-INS-RC • 04/14/2020 • ECN6926 • PAGE 5...
  • Page 6 3/8" flange nut (#6). Repeat on the other side of the vehicle. Then, make sure the base plate is level, and torque the hardware to 37 lb-ft. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70116-INS-RC • 04/14/2020 • ECN6926 • PAGE 6...
  • Page 7 For vehicles with a passenger-side temperature sensor: Remove the sensor from the back side of the bumper fascia, and use a zip tie to reattach it to the base plate. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70116-INS-RC • 04/14/2020 • ECN6926 • PAGE 7...
  • Page 8 When ready to tow, install the tow bar mounting tabs (#2). When not towing, insert the socket plugs (#8) into the ends of the tow bar base plate (#1). CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70116-INS-RC • 04/14/2020 • ECN6926 • PAGE 8...
  • Page 9: Safety Cable Installation

    Do not tow with worn or damaged parts. Vehicle manufacturer's recommendations Review the owner’s manual for your towed vehicle and towing vehicle for specific recommendations, capacities and requirements. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70116-INS-RC • 04/14/2020 • ECN6926 • PAGE 9...