Download Print this page

Advertisement

Quick Links

INSTALLATION MANUAL
Level of Difficulty
Difficult
Installation difficulty levels are based on time
and effort involved and may vary depending on
the installer level of expertise, condition of the
vehicle and proper tools and equipment.
Installed Attachment Tabs
Height
16-1/2"
Width
18"
Parts List
Item Qty Description
1
1
Tow bar base plate
2
2
Tow bar mounting tab
3
2
Safety cable, 7,500 lbs.
4
6
Square-hole spacer,
1/4" x 1" x 2"
5
6
Carriage bolt,
3/8"-16 x 1-1/2", grade 8
6
2
Hex bolt,
1/4"-20 x 1", grade 8
7
4
Hex bolt,
3/8"-16 x 1-1/4", grade 8
8
2
Flange nut, 1/4"-20, grade 5
9
6
Serrated-flange nut,
3/8"-16, grade 8
10
4
Nylock nut, 3/8"-16, grade 8
11
2
Quick link, 1/2"
12
2
Socket plug
Tools Required
Torque wrench
Drill
Socket, 9/16"
Drill bit, 1/4"
Socket, 7mm
Drill bit, 13/32"
Socket, 10mm
Hole saw, 1-1/4"
Wrench, 9/16"
Phillips screwdriver
Torx, T-15
Flat head screwdriver
Large vise grip
Tape measure
Fishwire, 3/8"
Utility knife
(includes 6)
CURTMFG.COM
PRODUCT SUPPORT: 877.287.8634
WARNING
Never exceed the vehicle manufacturer's recommended gross vehicle weight rating (GVWR).
Product Photo
Not pictured: Safety cables, quick links and socket plugs
CAUTION
Take care when cutting any plastic or metal as injury may occur if done improperly.
NOTICE
Visit www.curtmfg.com for a full-color copy of this
instruction manual, as well as helpful videos, guides and much more!
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
This installation requires fascia panels, coolant lines and a temperature sensor to be
temporarily removed and reinstalled. Some drilling and trimming are also required.
To help prevent damage to the product or vehicle, refer to the specified
torque specifications when securing hardware during the installation process.
If equipped, we recommend removing the base plate attachment tabs when not in use.
SAFETY INSTRUCTIONS
Safety glasses should be worn at all times while installing this product.
Product Registration and Warranty
CURT stands behind our products with industry-leading warranties. To get copies of the product
warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys
70123-INS-RA
07/23/2020
ECN6963
PAGE 1
70123

Advertisement

loading
Need help?

Need help?

Do you have a question about the 70123 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for curt 70123

  • Page 1 Tape measure Fishwire, 3/8" Utility knife Product Registration and Warranty (includes 6) CURT stands behind our products with industry-leading warranties. To get copies of the product warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 •...
  • Page 2 3/8"-16 x 1-1/4", grade 8 Flange nut, 1/4"-20, grade 5 Serrated-flange nut, 3/8"-16, grade 8 Nylock nut, 3/8"-16, grade 8 Quick link, 1/2" Socket plug Included fishwire CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70123-INS-RA • 07/27/2020 • ECN6963 • PAGE 2...
  • Page 3 Remove the rubber strip along the top, unhooking it from the radiator cover. Carefully pull straight up on the radiator cover to release the two clips underneath. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70123-INS-RA • 07/27/2020 • ECN6963 • PAGE 3...
  • Page 4 Pull the wheel well liner back and use a 7mm socket to remove the bolt on the inside edge. Repeat on the other side of the vehicle. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70123-INS-RA • 07/27/2020 • ECN6963 • PAGE 4...
  • Page 5 (either let it hang or spin it under the vehicle). For 2010 - 2014 models, remove the push pin from the back side of the temperature sensor. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70123-INS-RA • 07/27/2020 • ECN6963 • PAGE 5...
  • Page 6 1-1/4" hole saw or step drill. Then, reattach the coolant line, using the 1/4" back side holes and supplied hardware (#6, #8). CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70123-INS-RA • 07/27/2020 • ECN6963 • PAGE 6...
  • Page 7 There should be a 3-1/2" gap between the bottom of the bumper and the top of the base plate frame tube. With the base plate level, temporarily clamp it onto the frame. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70123-INS-RA • 07/27/2020 • ECN6963 • PAGE 7...
  • Page 8 37 lb-ft. Step 15 On 2010 – 2014 models, reinstall the temperature sensor, attaching it to the radiator with the included zip tie. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70123-INS-RA • 07/27/2020 • ECN6963 • PAGE 8...
  • Page 9 When ready to tow, install the tow bar mounting tabs (#2). When not towing, insert the socket plugs (#12) into the ends of the tow bar base plate (#1). CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70123-INS-RA • 07/27/2020 • ECN6963 • PAGE 9...
  • Page 10: Safety Cable Installation

    Do not tow with worn or damaged parts. Vehicle manufacturer's recommendations Review the owner's manual for your towed vehicle and towing vehicle for specific recommendations, capacities and requirements. CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 70123-INS-RA • 07/27/2020 • ECN6963 • PAGE 10...