Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Billion BEC MX-220-UT-5G
Summary of Contents for Billion BEC MX-220-UT-5G
- Page 1 MX-220-UT-5G Advanced Industrial 5G Router Installation Guide...
-
Page 2: Package Contents
MX-220-UT-5G Advanced Industrial 5G Router PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE. Package Contents Quick Start Guide MX-220-UT-5G RS232 DB9 Cable ANT-SX-5048 ant. -
Page 3: Device Leds
Installation Guide Device LEDs Item Description Green RSSI > -69dBm. Excellent signal. Green/ -69dBm > RSSI > -81dBm. Good signal. Fast Flashing Red/ -81dBm > RSSI > -99dBm. Fair signal. Fast Flashing (Cellular Signal Red/ Strength Indicator) -99dBm > RSSI. Poor signal. Slow Flashing No signal and the 5G NR module is in service. - Page 4 MX-220-UT-5G Advanced Industrial 5G Router Device Overview & Hardware Installation Connect to Power Source Mode 1. Attach the power converter with 3-pin terminal block to the MX-220-UT-5G and plug in the supplied power adapter or power supply system. Mode 2. Attach the power terminal block (TB) to the MX-220-UT-5G and connect wire leads from a power supply to the terminal block (TB) plug.
- Page 5 Installation Guide Connect to a Serial Device Serial port 1 & 2 support RS232, RS485 and RS422, connect one end of the serial cable to the console port of the serial device. Serial Port (RS-232, RS-485, RS-422) Pin Definition: RS-232 RS-485 RS-422 (DTE)
-
Page 6: Lan Connection
MX-220-UT-5G Advanced Industrial 5G Router Type 1: Normal: Trigger: Type 2: Normal: Trigger: LAN Connection Connect a Ethernet cable (Cat-5 or Cat-5e) to one of the LAN ports and the other side to the IED/ PLC/ PC’s Ethernet interface. (*Note: LAN1 automatically becomes an ethernet WAN port when the ETH WAN internet interface is being selected in the GUI.) RESET Button After the device is powered on, press it 6 seconds or above to restore to factory default settings... - Page 7 Installation Guide ANT-SX-5048 Installation...
- Page 8 MX-220-UT-5G Advanced Industrial 5G Router...
- Page 9 Installation Guide...
- Page 10 MX-220-UT-5G Advanced Industrial 5G Router Connect the LMR-240 extended cable (SMA male) to antenna (SMA female). After finishing connection, bundle each SMA connector by using waterproof tape. STEP 1: Connect the R/A SMA Adapter to each SMA male on the other end of LMR-240 extended cable.
-
Page 11: Hardware Installation
Installation Guide After finishing the previous two steps, connect the LMR-240 Extended Cable to the corresponding connector of device. Hardware Installation Before installation, please attach and fasten the wall mounting kit or din rail clip to the bracket holder of the MX-220-UT-5G. Wall MOUNTING There is a mounting location on the bracket holder of MX-220-UT-5G to mount the Wall mounting kit. -
Page 12: Din Rail Mounting
MX-220-UT-5G Advanced Industrial 5G Router Step 1. Install clip in the appropriate position. Attach and fasten the wall mounting kit to the bracket holder of the MX-220-UT-5G using two mounting screws included in this mounting kit. Step 2. 1. Hold the wall mount up to the wall at the installation site and mark each screw location on the wall. - Page 13 Installation Guide Step 2. Clip and secure the MX-220-UT-5G onto a DIN Rail. Hook the top of the clip onto the top edge of the DIN Rail. Make sure the clip is firmly against the rail. Push down the bottom of the MX-220-UT-5G to snap it onto the lower edge of the DIN rail. ...
- Page 14 2. A username and password window will appear. The default username is “admin”, and password is “admin”. Press OK to proceed. 3. You will get a status report web page and main menu screen. Contact Billion WORLDWIDE https://www.billion.com BEC Technologiesn Inc. (U.S.A.)
-
Page 15: Federal Communication Commission Interference Statement
Installation Guide Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Need help?
Do you have a question about the BEC MX-220-UT-5G and is the answer not in the manual?
Questions and answers