Jupio JBG-C006 Instruction Manual

Part Names
○,
Attachment screw
1
○,
2 Guide pin
○,
Attach/detach knob
3
○,
4 Battery release lever
○,
5 DC coupler cord mount
○,
6 Battery compartment release lever
○,
Electrical contacts
7
○,
Camera battery compartment cover slot
8
○,
Vertical-grip ON/OFF switch
9
○,
Vertical grip AE lock/FE
10
○,
lock/lndex/Reduce
11
○,
button
12
○,
Vertical-grip AF point selection/Magnify
13
button
○,
Battery compartment cover
14
○,
Battery compartment
15
○,
Vertical-grip shutter button
16
○,
Vertical-grip main dial
17
○,
Hand strap mount
18
○,
Tripod socket
19
○,
Battery magazine BGM-E2
20
○,
Protective cover
21
Jupio Battery Grip JBG-C006
Instruction Manual
Thank you for purchasing this outstanding Jupio product.
The JBG-C006 is a battery grip for the EOS 40D/30D/20D that can hold two
BP-511A or six AA size batteries. It is also equipped with a vertical-grip
shutter button, dial, AE lock/FE lock button, and AF point selection button to
enable shooting in the same way as a horizontal grip.
● Battery Pack Jupio for BP-514/511/512 is also available.
■ Attaching to the Camera
1. Remove the battery from the camera (Fig. 1).
2. Detach the camera's battery compartment cover.
● EOS40D: Place the camera on a desk or other flat surface and hold it
firmly so that it does not drop. Next, pull the battery compartment cover
while opened at a slanted angle to remove (Fig. 2-1).
● EOS30D/20D: Refer to Fig.2-2 to remove the battery compartment
cover.
3. Insert the detached cover into its storage slot to ensure that it will not be
lost (Fig. 3).
4. Remove the protective cover, and then insert the electrical contacts into
the battery compartment (Fig. 4-①).
5. Align the attachment screw with the camera's tripod socket, and then
turn the attach/detach knob to tighten securely (Fig. 4-②).
※ Be sure to attach the JBG-C006 to the camera before loading the power
supply in the JBG-C006. The results of the battery check may not be
displayed properly if you attach the JBG-C006 to the camera with the power
supply already inside.
※ Before removing the JBG-C006 from the camera, be sure to turn the
camera's power switch to <OFF>rand take out the JBG-C006 power supply.
After the JBG-C006 is removed, attach the protective cover to the electric
contacts.
■ Inserting the Battery Packs
1. Slide the lever as shown by the arrow and open the cover (Fig.5).
2. Press both release levers outward in the battery compartment, and
remove the battery magazine (Fig. 6).
3. Check the illustrations on the battery compartment cover, and insert the
battery packs all the way in (Fig. 7).
4. Close the battery compartment cover until it clicks into place.
※ If only one battery is used, it may be inserted in either the right
or left sides. If two battery packs are inserted, power is supplied
simultaneously by both battery packs.
※ Two battery packs at different charging levels or different types
can be used without any problems.
■ Inserting AA Size Batteries
1. Insert the batteries into the battery magazine (Fig. 8).Insert the batteries
with the + and - ends in the directions shown by the illustrations.
2. Turn over the battery magazine so that the inserted batteries are facing
downward, and then insert the battery magazine until the release lever locks
into place (Fig. 9).
3. Close the battery compartment cover.
Press the cover until it clicks into place.
▲ When AA size batteries are used, the continuous shooting speed during
Al Servo AF will slow down. Also fewer images can be shot. Therefore,
usage of AA size batteries is recommended only for emergencies. Use of
AA size batteries is also not recommended when connecting the camera
to a computer.
▲ When using throwaway AA size batteries, the camera may not function
when used at temperature below 200C/680F or for certain battery brands
and storage conditions. Also, insert six new batteries that are the same
brand. Do not use old and new batteries together.
■ Inserting the DC Coupler
To connect to a household power outlet, use the AC Adapter Kit
ACK-E2 (sold separately).
1. Connect the DC coupler to the AC adapter, and then connect the
power cord to a power outlet.
2. Load the DC coupler into the left side of the battery compartment
(Fig. 10-①), and pass the cord through the cord mount (Fig. 10-
②)．
3. Insert the DC coupler all the way in.
4. Check that the cord passes properly through the cord mount and
close the cover until it clicks into place.
▲ Do not connect or disconnect the power cord while the camera's
power switch is set to <ON>.
▲ The DC coupler can also be used with the Compact Power
Adapter CA-PS400 and DC Coupler DR-400 (both sold
separately).
■ Using the Battery Grip
● Turning the vertical-grip ON/OFF switch to <ON> (Fig. 11)
makes the JBG-C006 buttons and dials function in the same
way as those on the camera.
● When shooting in the horizontal-grip position, turn the
vertical-grip ON/OFF switch to <OFF> so that you do not
accidentally use the buttons or dials on the JBG-C006.
■ Caution
● Remove the power supply from the JBG-C006 when the camera
will not be used for an extended period.
● Never attempt to disassemble or repair the product. Any
malfunction or accident resulting from such action is not covered
by the warranty.
■ Battery Life
Temperature: +23℃/0℃ 73℉/32℉ [Number of shots . approx.]
Model Power supply No flash
EOS BP-511Ax2 2200/1900
40D
AA alkaline batteries 400/200
EOS BP-511Ax2 2200/1800
30D
AA alkaline batteries 400/200
EOS BP-511Ax2 2200/1500
20D AA alkaline batteries 250/0
● No Live View shooting, based on CIPA (Camera & Imaging
Products Association) testing standards.
● The number of images that can be shot is reduced by frequent
usage of the LCD monitor, holding the shutter button halfway
down for an extended time, and using the AF frequently without
shooting.
● The battery level can be checked on the LCD panel of the
camera.
■ Major Specifications
Type: Battery grip for the EOS 40D/30D/20D
Power sources: (1) Battery Pack BP-511A/514/511/512
(2) AA size batteries: Alkaline batteries
(3) AC Adapter Kit ACK-E2
Power switch: Camera's power switch
Dimensions: 142.7 (W) x 110.5 (H) x 75.7 (D) mm/
5.6 (W) x 4.4 (H) x 3.0 (D) in.
Weight: Approx. 325 g/11.5 0z. (not including the power
supply or battery magazine)
U.S.A. and Canada only:
The Lithium ion/polymer battery that powers
the product is recyclable. Please call l-800-8-
BATTERY for information on how to recycle this
Battery.
Jupio Europe b.v.
Wasaweg 27
9723 JD Groningen
The Netherlands
www.jupio.com
50%/flash
1600/1200
300/100
1400/1200
300/100
1400/1100
120/0