Jupio JBG-C008 Instructions Manual

Jupio Battery Grip JBG-C008
Instructions
Nomenclature
○, Protective cover. ○, Electrical contacts. ○, Attachment screw. ○,
1 2 3
Attach/detach knob.○, Battery magazine release handle.○,
6
button. ○, AE lock button. ○, AF start button. ○,
9
10 11
Multi-function button. ○, Camera battery compartment cover holder. ○,
14
compartment cover slot. ○, Main Dial. ○, Vertical-grip operation switch. ○,
16 17
mount. ○, Tripod socket. ○, Battery Magazine BGM-E11L (for LP-E6). ○,
19 20
compartment.○, Battery Magazine BGM-E11A (for size-AA/LR6 batteries).
22
The JBG-C008 is a battery grip that can hold two Battery Pack LP-E6 or six size-AA/LR6 batteries. It is
also equipped with a vertical-grip shutter button, Main Dial, etc. to enable shooting in the same way as
with horizontal grip.
■ Attaching to the Camera
1. Remove the battery from the camera (Fig. 1).
2, Detach the camera's battery compartment cover (Fig. 2).
3. Store the removed battery compartment cover in the storage slot.
● Push the lock lever of the battery compartment cover as shown by the arrow, insert the cover into
the battery compartment cover holder(① in Fig. 3-1), and press on the cover until it snaps into
place(② in Fig. 3-1).
● To remove the battery compartment cover, slide the battery compartment cover release lever to
unlock it (Fig. 3-2), and then remove the cover by performing the storage procedure in reverse.
4. Remove the protective cover, and then insert the electrical contacts into the battery compartment
(Fig. 4-①).
5. Align the attachment screw with the camera's tripod socket,and then turn the attach/detach knob to
tighten securely to the camera (Fig. 4-②).
▲ Be sure to attach the battery grip to the camera before inserting the batteries. The results of the
battery check may not be displayed properly if you attach the battery grip to the camera with the
batteries already inside.
▲ Before removing the battery grip from the camera, be sure to turn the camera's power switch to
<OFF>, and take out the batteries. After removing the batteries, attach the protective cover to
the electrical contacts.
■ Installing the Battery Packs
Guide pin. ○,
4 5
DG cord mount.○, AF point selection
7 8
Multi-controller. ○, Shutter button. ○,
12 13
Camera battery
15
Hand strap
18
Battery
21
1. After flipping out the release handle, turn it as shown by the arrow, and then pull out the battery
magazine (for size-AA/LR6 batteries) (Fig. 5).
2. Insert one or two Battery Pack LP-E6 into the battery magazine (for LP-E6) (Fig. 6).
3. Attach the battery magazine into the battery grip (Fig. 7-1).
After attaching, check that the battery magazine is securely attached to the battery grip.
4. Close the release handle (Fig. 7-2).
▲ If only one battery is used, it may be inserted in either the right or left side.
▲ If two batteries are inserted, power is supplied simultaneously by both batteries. Two batteries
with different charging levels can be inserted and used without any problems.
▲ Remove the battery packs LP-E6 or size-AA/LR6 batteries from the battery grip when the
camera will not be used for an extended period.
■ Inserting Size-AA/LR6 Batteries
1. Insert the batteries into the battery magazine (for size-AA/LR6 batteries) (Fig. 8).
Make sure the + and - battery contacts are properly oriented as shown in the illustration.
2. Attach the battery magazine into the battery grip (Fig. 9-1).
After attaching, check that the battery magazine is securely attached to the battery grip.
3. Close the release handle (Fig. 9-2).
▲ When size-AA/LR6 batteries are used, the high-speed continuous shooting speed during Al
Servo AF will be slower.
▲ Because the number of possible shots decreases when using size-AA/LR6 batteries, their usage
is recommended only for emergencies. Particularly during Live View shooting and movie
shooting, the number of possible shots (movie recording time) is greatly reduced.Depending on
the battery brand and storage conditions,the number of possible shots may be further reduced.
▲ With size-AA/LR6 batteries, use six new batteries of the same brand at temperatures above
200C/68QF. The camera may not function when used in low temperatures or when old and new
batteries are used together.
■
Using a Household Power Outlet
To connect to a household power outlet, use the AC Adapter Kit ACK-E6 (sold separately).
1. Connect the power cord to the AC adapter, and insert the prongs into a power outlet. Connect the
DC cord to the DC coupler. (Refer to ACK-E6 Instructions.)
2. Insert the DC coupler into the release-handle-side battery compartment of the battery magazine (for
LP-E6) (Fig. 10).
3. Pass the DC cord through the battery magazine cord groove (Fig. 11-1), and attach the battery
magazine to the battery grip. When attaching the battery magazine, pass the DC cord through the
battery grip DC cord mount (Fig. 11-2).
▲ Always set the camera's power switch to <OFF> before disconnecting the power cord.
▲ Be careful that the DC cord does not get pinched between the battery grip and the battery
magazine.
■ Using the Battery Grip
● Turning the vertical-grip operation switch to <ON> (Fig. 12) makes the battery grip buttons and dial
function in the same way as those on the camera.
● When shooting in the horizontal-grip position, turn the vertical-grip operation switch to <OFF> so that
you do not accidentally use the buttons or dial on the battery grip.
● The battery level can be checked on the camera.
● Refer to the back of this sheet for instructions about the provided soft case.
● Hand Strap E2 (sold separately) can be used for enabling a more secure grip.
■
Specifications
Battery: (1) One or two Battery Packs LP-E6
(2) Six size-AA/LR6 Alkaline batteries
(3) AC Adapter Kit ACK-E6
Camera's power switch
Power switch:
Refer to your camera's Instruction Manual.
Possible shots:
Working temperature range:
0℃- +40℃ / 32℉ - +104℉
Working humidity: 85% or less
Dimensions: Approx. 153.1 (W) x 114.5 (H) x 85.3 (D) mm/
6.0 (W) x 4.5 (H) x 3.4 (D) in.
Weight: Approx. 310 g/10.9 oz. (without batteries and battery magazine)
● All the specifications above are based on Canon's testing standards.
● The product specifications and exterior are subject to change without notice.
USA and Canada only:
The Lithium ion/polymer battery is recyclable. Please call 1-800-8-BATTERY for
information on how to recycle this battery.