Jupio JBG-C005 Instructions

Jupio Battery Grip JBG-C005
○,
Part Names Vertical-grip operation switch
11
○, ○,
Protective cover Shutter button
1 12
○, ○,
Electrical contacts Camera battery compartment
2
13
○,
Attachment screw cover slot
3
○, ○,
Guide pin Main Dial
4
14
○, ○,
Attach/detach knob Hand strap mount
5
15
○, ○,
Battery magazine release Tripod socket
6 16
○,
handle Battery Magazine (for LP-E6)
17
○, ○,
DC cord mount Battery pack compartment
7 18
○, ○,
AF point selection/Magnify Battery Magazine (for
8
19
button size-AA/LR6 batteries)
○,
AE LOCK/FE
9
lock/lndex/Reduce button
○,
AF start button
10
Battery Grip JBG-C005 Instructions
Thank you for purchasing the product.
The JBG-C005 is a battery grip that can hold two Battery Pack LP-E6 or
six size-AA/LR6 batteries. It is also equipped with a vertical-grip shutter
button, Main Dial, etc.to enable shooting in the same way as with
horizontal grip.
■ Attaching to the Camera
1. Remove the battery from the camera. (Fig. 1)
2. Pull out the camera's battery compartment cover at a slanted angle to
detach. (Fig. 2) Perform the operation on a table so as not to drop the
camera.
3. Insert the detached cover into its storage slot to ensure that it will not
be lost. (Fig. 3-1) When taking out the cover, press lightly on the cover
hinge and pull it out upward at a slanted angle. (Fig. 3-2)
4.Remove the protective cover, and then insert the electrical contacts into
the camera battery compartment.(Fig. 4-① )
5. Align the attachment screw with the camera's tripod socket, and then
turn the attach/detach knob to tighten securely.(Fig. 4-② )
▲ Do not further push open the battery compartment cover when it is
already open. Doing so may damage its hinge.
▲ Be sure to attach the battery grip to the camera before inseritng the
batteries.The results of the battery check may not be displayed
properly if you attach the battery grip to the camera with the batteries
already inside.
▲ Before removing the battery grip from the camera,be sure to turn
the camera's power switch to<OFF>,and take out the batteries.After
removing the batteries,attach the protective cover to the electrical
contacts.
■ Installing the Battery Packs
1. After flipping out the release handle, turn it as shown by the arrow, and
then pull out the battery magazine(for size-AA/LR6 batteries).(Fig.5)
2. Insert one or two Battery Pack LP-E6 into the battery magazine (for
LP-E6).(Fig.6).
3. Attach the battery magazine into the battery grip.(Fig. 7-1) After
attaching, check that the battery magazine is securely attached to the
battery grip.
4. Close the release handle.(Fig. 7-2)
※ If only one battery pack is used, it may be inserted in either the right
or left side.
※ If two battery packs are inserted,power is supplied simultaneously
by both battery packs.Two battery packs with different charging levels
can be inserted and used without any problems.
※ Remove the battery packs or size-AA/LR6 batteries from the
battery grip when the camera will not be used for an extended period.
■ Inserting Size-AA/LR6 Batteries
1. Insert the batteries into the Battery Magazine BGM-E9A (for
size-AA/LR6 batteries). (Fig. 8) Make sure the + and - battery contacts
are properly oriented as shown in the illustration.
2. Attach the battery magazine into the battery grip. (Fig. 9-1) After
attaching, check that the battery magazine is securely attached to the
battery grip.
3. Close the release handle.(Fig. 9-2)
▲ Fewer images can be shot when using size-AA/LR6
batteries.Also,the number of possible shots may vary depending
on the batteries brand and storage consitions,so usage of
size-AA/LR6 batteries is recommended only for emergencies.
▲ With size-AA/LR6 batteries,use six new batteries of the same
brand at temperatures above 20℃/68℉.The camera may not
function when uses in low temperatures or when old and new
batteries are used together.
■ Using a Household Power Outlet
To connect to a household power outlet, use the AC Adapter Kit ACK-E6
(sold separately).
1. Connect the power cord to the AC adapter, and insert the prongs into a
power outlet. Connect the DC cord to the DC coupler.(Refer to ACK-E6
Instructions.)
2. Insert the DC coupler into the release-handle-side battery pack
compartment of the battery magazine(for LP-E6).(Fig. 10)
3. Pass the DC cord through the battery magazine cord groove (Fig.
11-1), and attach the battery magazine to the battery grip. When
attaching the battery magazine, pass the DC cord through
the battery grip DC cord mount(Fig. 11-2)
▲ Always set the camera's power switch to<OFF>before
disconnecting the power cord.
▲ Be careful that the DC cord does not get pinched between the
battery grip and the battery magazine.
■ Using the Battery Grip
● Turning the vertical-grip operation switch to <ON>(Fig. 12) makes the
battery grip buttons and dial function in the same way as those on the
camera.
● When shooting in the horizontal-grip position, turn the vertical- grip
operation switch to <OFF> so that you do not accidentally use the
buttons or dial on the battery grip.
● The battery level can he checked on the camera.
● Hand Strap El(sold separately)can be used for enabling a more secure
grip.
■ Specifications
Battery: (1) One or two Battery Packs LP-E6
(2) Six size-AA/LR6 Alkaline batteries
(3)AC Adapter Kit ACK-E6
Power switch: Camera's power switch
Possible shots: Refer to your camera's Instruction Manual.
Working temperature range:
O℃- + 40℃/32℉-104℉
Working humidity:85% or less
Dimensions: Approx. 145.6(W) x 111.3(H) x 85.3(D) mm/
5.7(W) x 4.4(H) x 3.4(D)in.
Weight: Approx. 295 g/10.4 oz.(without batteries and battery
magazine)
● All the specifications above are based on Canon's testing standards.
● The product specification and exterior are subject to change without
notice.
Jupio Europe b.v.
Wasaweg 27
9723 JD Groningen
The Netherlands
www.jupio.com