Jupio JBG-C003 Instruction Manual

Part Names
○,
.Protective cover
1
○,
.Electrical contacts
2
○,
.Camera battery compartment cover slot
3
○,
.Battery compartment release lever
4
○,
.Attachment screw
5
○,
.Guide pin
6
○,
.Attach/detach knob
7
○,
.Battery release lever
8
○,
.DC coupler cord mount
9
○,
.Battery compartment cover
10
○,
.Battery compartment
11
○,
.AF point selection/Magnify button
12
○,
.AE lock/lndex/Reduce button
13
○,
.AF start button
14
○,
.Shutter button
15
○,
.Multi-function button
16
○,
.Main Dial
17
○,
.Vertical-grip operation switch
18
○,
.Hand strap mount
19
○,
.Tripod socket
20
○,
.Battery Magazine BGM-E6
21
Jupio Battery Grip JBG-C003
Instructions Manual
Thank you for purchasing this original Jupio product.
The JBG-C003 is a battery grip that can hold two Battery Packs LP-E6 or six
size-AA/LR6 batteries. It is also equipped with a vertical-grip shutter button, Main Dial,
etc. to enable vertical shooting with the same ease as horizontal shooting.
Attaching to the Camera
1. Remove the battery from the camera (Fig. 1),
2, Detach the camera's battery compartment cover (Fig, 2).
3. Insert the detached cover into its storage slot to ensure that it will not be lost (Fig, 3).
4. Remove the protective cover, and then insert the electrical contacts into the battery
compartment (Fig. 4-①).
5. Align the attachment screw with the camera's tripod socket,and then turn the
attach/detach knob to tighten securely to the camera Fig, 4-②).
▲ Be sure to attach the battery grip to the camera before inserting
the batteries. The results of the battery check may not be
displayed properly if you attach the battery grip to the camera
with the batteries already inside.
▲ Before removing the battery grip from the camera, be sure to
turn the camera's power switch to <OFF>, and. take out the
batteries. After removing the batteries, attach the protective
cover to the electrical contacts.
■ Inserting the Battery Packs
1. Slide the lever as shown by the arrow and open the cover (Fig. 5).
2. Press both release levers outward in the battery compartment,and remove the
battery magazine (Fig. 6).
3. Insert one or two Battery Packs LP-E6 in the orientation shown on the battery
compartment cover (Fig. 7).
4. Close the battery compartment cover until it clicks into place.
● lf only one battery pack is used, it may be inserted in either the right or left sides.
● If two battery packs are inserted, power is supplied simultaneously by both battery
packs. Two battery packs with different charging levels can be inserted and used without
any problems.
● Remove the battery packs from the battery grip when the camera will not be used for
an extended period.
■ Inserting Size-AA/LR6 Batteries
1. Insert the batteries into the Battery Magazine BGM-E6 (Fig. 8).Make sure the + and
- battery contacts are properly oriented as shown in the illustration.
2. Turn over the battery magazine so that the inserted batteries are facing downward,
and then insert the battery magazine until the release levers lock into place (Fig. 9).
3. Close the battery compartment cover uritil it clicks fnto place.
● Fewer images can be shot when using size-AA/LR6 batteries.Also, fewer images can
be shot depending on the battery brand and starage conditions, and so usage of size
AA/LR6 batteries
is recommended only for emergencies.
● With size-AA/LR6 batteries, use six new batteries of the same brand at temperatures
above 20℃/68℉.. The camera may not function when used in low ternperatures or
when old and new batteries are used together.
Jupio Europe b.v.
Wasaweg 27
9723 JD Groningen
The Netherlands
www.jupio.com
Using a Household Power Outlet
To connect to a household power outlet, use the AC Adapter Kit
1. Connect the DC coupler plug to the AC adapter.Connect the power cord to the AC
adapter, and insert the prongs into a power outlet.
2. Load the DC coupler into the left sioe of the battery compartment (Fig. 10-① ), and
pass the cord through the cord mount (Fig. 10-② ).
▲ Do not connect or disconnect the power cord while the camera's power switch
is set to <ON>.
Using the Battery Grip
●Turning the vertical-grip operation switch to <ON> (Fig. 11) makes the battery grip
buttons and dial function in the same way as those on the camera.
●When shooting horizontally, turn the vertical-grip operation switch to <OFF> so that
you do not accidentally use the buttons or dialon the battery grip.
●Hand Strap E-1 (sold separately) can be used for enabling a more secure grip.
●The battery level can be checked on the LCD panel of the camera and in the
viewfinder.
Specifications
Power sources: (1) One or two Battery Packs LP-E6
(2) AA alkaline/LR6 batteries x 6
(3) AC Adapter Kit ACK-E6
Power switch: Camera's power swttch
Possible shots: Refer to your camera's lnstruction Manual.
Working temperature range:
0℃ - +40℃ / 32℉ - 104℉
Working humidity: 85% or less
Dimensions: 147.4 (W) x 114.3 (H) x 76.9 (D) mm/
5.8 (W) x 4,5 (H) x 3.0 (D) in.
Weight: Approx, 340 g/12.0 oz. (not including the power supply or battery
magazine)
USA and Canada only:
The Lithium ion/polymer battery is recyclable. Please call
1-800-8-BATTERY for information on how to recycle this
battery.
Le Canada et les Etats-Unis seulement :
La batterie aux ions de Iithium est recyclable. Pour obtenir
des renseignements sur les fçcons de recycler cette batterie,
veuillez appeler au 1-800-8-BATTERY.
Los EE.UU. y Canadá solamente:
La batería de ion de Iitio es reciclable. Llame por favor
1-800-8-BATTERY para la información sobre cómo reciclar
esta batería.