Subscribe to Our Youtube Channel
Related Manuals for H3C Aolynk UAP622MG-AX30
Summary of Contents for H3C Aolynk UAP622MG-AX30
- Page 1 H3C Aolynk UAP622MG-AX30 Access Point Installation Guide New H3C Technologies Co., Ltd. http://www.h3c.com Document version: AW100-20250315...
- Page 2 The information in this document is subject to change without notice. All contents in this document, including statements, information, and recommendations, are believed to be accurate, but they are presented without warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions contained herein.
- Page 3 Preface This installation guide describes the installation procedure for the H3C Aolynk UAP622MG-AX30 access point. This preface includes the following topics about the documentation: • Audience. • Conventions. • Documentation feedback. Audience This documentation is intended for: • Network planners.
- Page 4 Symbols Convention Description An alert that calls attention to important information that if not understood or followed WARNING! can result in personal injury. An alert that calls attention to important information that if not understood or followed CAUTION: can result in data loss, data corruption, or damage to hardware or software. An alert that calls attention to essential information.
-
Page 5: Documentation Feedback
Documentation feedback You can e-mail your comments about product documentation to info@h3c.com. We appreciate your comments. -
Page 6: Table Of Contents
Contents Preparing for installation ················································································ 1 Safety labels ··············································································································································· 1 General safety recommendations ·············································································································· 1 Site preparation ·················································································································································· 1 Installation accessories ······································································································································ 2 Installation tools ················································································································································· 2 Installing the AP ····························································································· 1 Installation flowchart··········································································································································· 1 Pre-installation tasks ·········································································································································· 1 Determining the installation position ·················································································································· 2 Mounting the AP·················································································································································... -
Page 7: Preparing For Installation
Preparing for installation Safety labels Safety label Description Hot surface warning label. A device attached with this label might have a hot surface during operation. Install the device in a restricted access location. Only servicing engineers or trained personnel can operate the devices in the access location. -
Page 8: Installation Accessories
Installation accessories Figure1-1 Accessories provided with the AP Installation tools When installing the AP, you might need the following tools. Prepare the installation tools yourself as required. Figure1-2 Installation tools... -
Page 9: Installing The Ap
Installing the AP Installation flowchart Figure1-3 Installation flowchart Start Complete pre- installation tasks Determine the installation position On a wall On a ceiling Complete the AP installation and cable connection operations Troubleshoot the Power on the AP Operating Power off the AP correctly? Connect the AP to the network... -
Page 10: Determining The Installation Position
• The AP is typically installed on a high position. As a best practice, access and configure the AP before installing it. • If a cable is routed outdoors, make sure a lighting arrester is attached to the AP port. Prepare a lighting arrester yourself as needed. -
Page 11: Mounting The Ap On A Wall
(1) Installation hole for securing the mounting bracket to a wall or ceiling (point A) (4) 86 panel installation holes used to attach the mounting bracket to an 86 panel. The distance between the two holes is 60 mm (2.36 in) (5) Thread a cable through the hole to connect the AP (6) Security hole for an M3 ×... - Page 12 Figure1-7 Hammering the screw anchor into the wall Thread the M3 × 23.5 security screw through the security hole in the mounting bracket. Make sure the screw does not block the keyhole slot. Figure1-8 Inserting the security screw Insert the screws through the installation holes in the mounting bracket into the holes in the wall.
-
Page 13: Mounting The Ap On A Ceiling
Figure1-10 Attaching the AP to the mounting bracket Use a security Torx screwdriver to fasten the M3 × 23.5 security screw. Figure1-11 Fastening the M3 × 23.5 security screw Mounting the AP on a ceiling CAUTION: The ceiling for installing the AP must be less than 18 mm (0.71 in) in thickness, and can bear a load of 5 kg (11.02 lb). - Page 14 Remove the ceiling tile. Place the mounting bracket against the ceiling tile and mark the installation holes on the ceiling tile. Drill three holes with a diameter of 6 mm (0.24 in) at the marked positions, as shown in Figure1-12. Figure1-12 Drilling holes in the ceiling tile Thread the pan-head screws through the installation holes in the mounting bracket and into the holes in the ceiling tile.
-
Page 15: Connecting The Ap To A Power Source
Figure1-14 Attaching the AP to the mounting bracket (Optional.) You can use a cable tie to secure the cable before attaching the AP to the mounting bracket. First thread the cable tie through the auxiliary hole in the mounting bracket, leaving the cable tie unfastened, and then adjust the cable length and fasten the cable tie to secure the cable. -
Page 16: Connecting A Local Power Source
Figure1-16 Powering the AP through PoE Connecting a local power source You can use an AC/DC power adapter to connect the AP to a local power source. No power adapter is provided with the AP. Prepare one yourself as required. Table1-2 describes the power adapter specifications. -
Page 17: Check After Power-On
AP has been connected to the network. Logging into the device The AP supports several methods for device management and service configuration. You can select one method as needed. For more information, see H3C Aolynk APs Login Guide. - Page 18 Contents Appendix A Hardware Information and Specifications ································· 1 AP view ······························································································································································ 1 LEDs ·································································································································································· 1 Technical specifications ····································································································································· 1...
-
Page 19: Appendix A Hardware Information And Specifications
Appendix A Hardware Information and Specifications AP view Figure1-1 AP view LEDs Table1-1 LED descriptions LED status Description No power is present or the LED has been turned off. Steady on The AP is initializing, or an initialization exception has occurred. Yellow Flashing (twice per The Ethernet interfaces are down and no mesh links are... - Page 20 • One Power port. The AP also has a reset button and a security slot. The security slot is 7 × 3 mm (0.28 × 0.12 in) in size. Figure1-2 Ports on the AP (1) 2.5GE/PoE+ port (2) RESET button (3) Power port (4) Security slot Table1-2 Technical specifications...
Need help?
Do you have a question about the Aolynk UAP622MG-AX30 and is the answer not in the manual?
Questions and answers