Related Manuals for H3C Aolynk UAP512G-AC13
Summary of Contents for H3C Aolynk UAP512G-AC13
- Page 1 H3C Aolynk UAP512G-AC13 Access Point Installation Guide New H3C Technologies Co., Ltd. http://www.h3c.com Document version: AW100-20250315...
- Page 2 The information in this document is subject to change without notice. All contents in this document, including statements, information, and recommendations, are believed to be accurate, but they are presented without warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions contained herein.
- Page 3 Preface This installation guide describes the installation procedure for the H3C Aolynk UAP512G-AC13 access point. This preface includes the following topics about the documentation: • Audience. • Conventions. • Documentation feedback. Audience This documentation is intended for: • Network planners.
- Page 4 Symbols Convention Description An alert that calls attention to important information that if not understood or followed WARNING! can result in personal injury. An alert that calls attention to important information that if not understood or followed CAUTION: can result in data loss, data corruption, or damage to hardware or software. An alert that calls attention to essential information.
-
Page 5: Documentation Feedback
Documentation feedback You can e-mail your comments about product documentation to info@h3c.com. We appreciate your comments. -
Page 6: Table Of Contents
Contents Preparing for installation ················································································ 1 Safety recommendations ··································································································································· 1 Safety labels ··············································································································································· 1 General safety recommendations ·············································································································· 1 Site preparation ·················································································································································· 1 Installation accessories ······································································································································ 2 Installation tools ················································································································································· 2 Installing the AP ····························································································· 3 Installation flowchart··········································································································································· 3 Pre-installation tasks ·········································································································································· 3 Determining the installation position ··················································································································... -
Page 7: Preparing For Installation
Preparing for installation Safety recommendations Safety labels Safety label Description Hot surface warning label. A device attached with this label might have a hot surface during operation. Install the device in a restricted access location. Only servicing engineers or trained personnel can operate the devices in the access location. -
Page 8: Installation Accessories
Item Specification Operating humidity 5% RH to 95% RH, noncondensing Installation accessories Figure 1 Accessories provided with the AP Installation tools When installing the AP, you might need the following tools. Prepare the installation tools yourself as required. Figure 2 Installation tools... -
Page 9: Installing The Ap
Installing the AP Installation flowchart Figure 3 Installation flowchart Start Complete pre- installation tasks Determine the installation position Mount the AP On a wall On a junction box On a ceiling Mount the AP Connect the AP to the power source Connect the AP to the network... -
Page 10: Determining The Installation Position
• If a cable is routed outdoors, make sure a lighting arrester is attached to the AP port. Prepare a lighting arrester yourself as needed. Determining the installation position Determine the installation position by observing the following principles: • Few obstacles such as wall exist between the AP and clients. •... -
Page 11: Mounting The Ap On A Wall
Figure 5 Device Mounting the AP on a wall Place the mounting bracket against the wall and mark the installation holes on the wall. Figure 6 Marking the installation holes on the wall Drill two holes with a diameter of 7 mm (0.315 in) and a depth of 30 mm (1.18 in) at the marked locations, as shown in Figure Figure 7 Drilling holes in the wall... - Page 12 Figure 8 Hammering the screw anchor into the wall Remove the U-shaped plastic plate on the wall side for wiring, feed the Ethernet cable through the cable hole, and then secure the wall bracket to the wall using screws, as shown in Figure The wall bracket has side A and side B.
- Page 13 Figure 10 Connect an Ethernet cable Align the screw holes on two sides of the AP with those on the wall bracket, use the screws to secure the AP to the wall bracket, as shown in Figure Figure 11 Mounting the device Install the AP cover, as shown in Figure 12.
-
Page 14: Mounting The Ap On A Junction Box
Figure 12 Mounting the device Mounting the AP on a Junction box Connect an Ethernet cable with an RJ-45 connector to the GE/PoE port on the rear of the AP. Figure 13 Connect an Ethernet cable Align the screw holes on the two sides of the AP with those on the junction box, use screws to secure the AP to the junction box, as shown in Figure... - Page 15 Figure 14 Connect an Ethernet cable Reinstall the AP cover, as shown in Figure Figure 15 Reinstall the AP cover...
-
Page 16: Mounting The Ap On A Ceiling
Mounting the AP on a ceiling CAUTION: When you use the ceiling installation, the M4 screws provided with the AP require that the ceiling must be less than 15 mm (0.59 in) in thickness. If the ceiling is thicker, prepare longer M4 screws yourself. - Page 17 Figure 18 Secure the AP to the ceiling Connect an Ethernet cable to the uplink port on the rear of the AP. Figure 19 Connect an Ethernet cable Install the cover of the AP.
-
Page 18: Connecting The Ap To A Power Source
Figure 20 Install the cover of the AP Connecting the AP to a power source You can supply power to the AP through 802.3af-compliant PoE as required. Connecting a PoE power source To power the AP through PoE, use an Ethernet cable to connect an Ethernet port on a PoE switch to the GE/PoE port on the AP. -
Page 19: Logging Into The Device
Figure 21 Connecting the AP to the network Logging into the device The AP supports several methods for device management and service configuration. You can select one method as needed. For more information, see H3C Aolynk APs Login Guide. - Page 20 Contents Appendix A Hardware Information and Specifications ································· 1 LEDs ·································································································································································· 1 Ports ··································································································································································· 1 Technical specifications ····································································································································· 3...
-
Page 21: Appendix A Hardware Information And Specifications
Appendix A Hardware Information and Specifications LEDs Figure1-1 LEDs Table1-1 LED descriptions LED status Description No power is present or the LED has been turned off. Steady on The AP is initializing, or an initialization exception has occurred. Yellow Flashing (twice per The Ethernet interfaces are down and no mesh links are second) established. - Page 22 • One GE port. The AP also has a reset button. Figure1-2 Ports on the AP (1) RESET button (1) 10/100/1000M Ethernet port...
-
Page 23: Technical Specifications
(1) UpLink GE/PoE_IN port Table1-2 Port descriptions Port Standards and protocols Description • To reboot the AP, press and hold the button for no more than 5 seconds. • To reset the password, press and hold the button for 5 to 10 seconds until the LED is RESET flashing yellow at 1 Hz.
Need help?
Do you have a question about the Aolynk UAP512G-AC13 and is the answer not in the manual?
Questions and answers