Contents And Ratings - FUTABA FP-8SSHP Instruction Manual

•The receiver is a miniature PCM receiver in
which the highest reliability has been pursued.
It is the first R/C receiver in the world to use
the newest computer technology.
•Miniature PCM receiver with hi-speed single-
chip microprocessor. Resistance against adja-
cent band and noise interference has been
increased by one full order of magnitude.
•Microprocessor-controlled servo hold function
eliminates erroneous operation when the
"dead point" area is entered.
•Microprocessor provides fail-safe and battery
fail-safe functions for greater safety.
•Error lamp display allows checking of the
receiver operating state.
•DC-DC converter in the power supply im-
proves the low-voltage operation character-
istic.
•High sensitivity design with RF amplifier
circuit.
•Ultra narrow-band ceramic filter and PCM
system are practically invulnerable to adjacent
band interference.
•Gold-plated
contact. Polarized housing increases reliability
2
against shock and vibration.

•CONTENTS AND RATINGS

Ratings and specifications are subject to change without prior notice.
Model
Transmitter
Receiver
Servo
Switch
Nicd battery
Accessories
Transmitter FP-T8SSHP————————————
Operating system
Transmitting frequency
Modulation
Power requirement
Current drain
Charger FBC-8B12L
Input voltage
Output
connector pins eliminate poor
Charger, extension cord, DSC cord (FSC-1), CHG adaptor, DSC-CHG cord, frequency
flag, spare horn, mounting screws, tachometer sensor (FTA-3)
Receiver FP-R118GP______________
: Single-stick, 8 channels for Receiving frequency
helicopter
: 50/53MHZ BANDSIChosen Intermediate frequency
72/75MHz BANDS[band Power requirement
53MHz • • 72MHz
Frequency change to any Current drain
of above bands Is possible Dimensions
by merely changing RF
module. Weight
: PCM (FM) Receiving range
: 9.6V 8/500mAH internal
Nicd battery (NT.8H)
: 250mA
Receiver and servo Nicd battery NR-4J_
: 120VAC, 50/60H2.4VA Voltage
: Tx side 9.6V. 45mA
Dimensions
Rx side 4.8V. 45mA
Weight
•DSC circuit. Each servo can be controlled
from the transmitter without turning on the
transmitter
directly to the C terminal.
•New indirect-drive
vibration and shock resistance and improves
neutral precision tremendously.
•Futaba low-power custom 1C provides high
starting torque, narrow dead band, and excel-
lent trackability.
•Fiberglass-reinforced PBT (polybutylene ter-
ephthalate) injection molded servo case is
mechanically strong and invulnerable to glow
fuel.
•Strong polyacetal resin ultra-precision servo
gear features smooth operation, positive neu-
tral, and very little backlash.
•Fiberglass-reinforced epoxy resin PC board
with thru-the-hole plating improves servo amp
vibration and shock resistance.
•Thick-film gold plated connector pins ensure
positive contact and greater reliability against
shock and vibration. The connector housing is
polarized to prevent reverse insertion.
•Six special adjustable splined horns are avail-
able.
FP-8SSHP
FP-T8SSHP x 1 with module FP-TF-FM
FP-R118GPx 1
F P - S 1 3 0 x 4
SWH-5 (R4-SWJ) x 1
NR-4Jx 1
: 50/53MHz BANDSIChosen
72/75MHz BANDS) band
: 455kHz
. 4.8V Nicd battery (NR-4J-
shared with servo)
: 42mA (at 4.8V reception)
: 2.23 x 1.65 x 0.94 in
(57 x 42 x 24mm)
:1.85ozl53g)
: 500m on the ground
1000m in the air
When FP.T8SSHP used
(at the best conditions)
4.8V.4/500mAH
: 2.01 x 2.28 x 0.59 in
151 x 5 8 x 15mm)
: 3.350Z (95g)
by connecting the transmitter
potentiometer
Servo FP-S130_________________
Control system - + p u l s e width control
1520uS.N
Operating angle : One side 4 5 " o r more (in-
cluding trim)
Power requirement : 4.8V (shared with receiver)
Current drain : 5mA (at idle)
Output torque : 55.6oz-in (4kg-cm)
Operating speed : 0.24sec/60°
Dimensions : 1.52 x .77 x 1.36 in
l 3 8 . 5 x l 9 . 5 x 3 4 . 5 m m )
Weight : 1 . 4 7 o z ( 4 2 g l
improve