Advertisement
Quick Links
OPERATING INSTRUCTIONS + TROUBLESHOOTING GUIDE
A. INITIAL SETUP
1.
Make sure the worksurface is securely affixed to the mechanism.
2.
Please be sure the area around the table is clear of any obstructions.
3.
Your Offices to Go Height Adjustable Table Base comes out of the box ready to use. Just plug into a standard outlet and enjoy.
B. OPERATION
1.
Press and hold the
or
height of 27.8" when measured to the top of the Offices to Go (OtG) 1" Laminate Top.
C. MEMORY SETTINGS
Once you have adjusted the desk to your desired height, you can set the height to a memory key on the handset.
s
1.
Press the
button. Then press the number on the handset where you want the position stored. You may store up to three positions
1
using numbers
through
a.
If no selection is made within 10 seconds, the screen will stop flashing and will leave the Memory Settings mode.
2.
Once you have set your memory position, simply press the number on the handset and the table will automatically adjust to the
stored height. To stop the table during automatic adjustment, tap any button on the handset.
D. SETTINGS MENU
1.
Press and hold the button
been entered.
2.
Press the
and
buttons to selection
3.
If no selection is made within 10 seconds, the screen will stop flashing and will leave the Settings menu.
MODE
FUNCTION
5- 1
Pinch and Collision
Protection
Change the sensitivity of
the pinch and collision
protection settings.
officestogo.com
revised 06182024
OTGHABASE3 HEIGHT ADJUSTABLE TABLE
to set the table to your desired position. The table will reach a maximum height of 45.5" and minimum
3
on the handset.
s
for about three seconds; the screen will flash the
5- 1
5-2
,
1. While the display shows
Pinch + Collision Protection settings menu, and the screen will display the current
parameters.
L1
= Lowest Sensitivity
L2
= Medium Sensitivity
L3
= Highest Sensitivity
OFF
= Turn off this function
2. Press
or
s
S
and hold the
s
3. Press the
button again to leave this settings menu.
5-
5-3
5-4
5-5
,
,
,
.
SETTING STEPS
1
5-
, press and hold the
L1
L2
L3
buttons to select
,
,
button for 3 seconds to save it.
1
indicating that the settings menu has
s
button for 3 seconds to enter the
OFF
or
. Once your selection is made, press
1
Advertisement
Related Manuals for Offices To Go OTGHABASE3
Summary of Contents for Offices To Go OTGHABASE3
- Page 1 Make sure the worksurface is securely affixed to the mechanism. Please be sure the area around the table is clear of any obstructions. Your Offices to Go Height Adjustable Table Base comes out of the box ready to use. Just plug into a standard outlet and enjoy. B. OPERATION Press and hold the to set the table to your desired position.
- Page 2 OTGHABASE3 HEIGHT ADJUSTABLE TABLE OPERATING INSTRUCTIONS + TROUBLESHOOTING D. SETTINGS MENU MODE FUNCTION SETTING STEPS Calibrating the 1. Your table comes out of the box calibrated to its height limits when paired with an Offices to Go Laminate 1” Laminate Top. However, there may be a need after installation to adjust the Height handset readout, i.e., if using alternate tops of varying thicknesses.
- Page 3 OTGHABASE3 HEIGHT ADJUSTABLE TABLE OPERATING INSTRUCTIONS + TROUBLESHOOTING E. RESETTING THE BASE AFTER RECONFIGURATION Please be sure the area around the table is clear of any obstructions. Press and hold the for 3 seconds. The screen will flash and begin the initialization process. The table will automatically go to the lower limit of the table.
- Page 4 OTGHABASE3 HEIGHT ADJUSTABLE TABLE OPERATING INSTRUCTIONS + TROUBLESHOOTING F. ERROR CODE SUMMARY DISPOSITION ERROR CODE DEFINITION DESCRIPTION Motor 1 Not The motor cable is disconnected or loose Insert the motor plug back into the Connected during operation. control box. Perform a reset.
Need help?
Do you have a question about the OTGHABASE3 and is the answer not in the manual?
Questions and answers