Hard Disk Drives - Asus PUNDIT-AE3 Manual

Barebone system
Hide thumbs Also See for PUNDIT-AE3:
Table of Contents

Advertisement

2 .
2 . 2 .
2 .
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
2 .
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA

hard disk drives.

SATA connectors
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
3 .
3 . 3 .
C P U a n d C h a s s i s f a n c o n n e c t o r s
C P U a n d C h a s s i s f a n c o n n e c t o r s
3 .
3 .
C P U a n d C h a s s i s f a n c o n n e c t o r s
C P U a n d C h a s s i s f a n c o n n e c t o r s
C P U a n d C h a s s i s f a n c o n n e c t o r s
( 4 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
( 4 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
( 4 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
( 4 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
( 4 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
The fan connectors support cooling fans of 350 mA~740 mA (8.88 W
max.) or a total of 1 A~2.22 A (26.64 W max.) at +12V. Connect the
fan cables to the fan connectors on the motherboard, making sure that
the black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! Do not place jumper caps on the
fan connectors!
Fan connectors
4 - 6
4 - 6
4 - 6
4 - 6
4 - 6
®
You must install Windows
Service Pack1 before using Serial ATA hard disk drives.
When using the connectors in standard IDE mode, you can connect the
primary (boot) hard disk drive to any of the SATA connectors.
®
SATA2
SATA1
®
2000 Service Pack 4 or the Windows
CHA_FAN
CPU_FAN
C h a p t e r 4 : M o t h e r b o a r d i n f o
C h a p t e r 4 : M o t h e r b o a r d i n f o
C h a p t e r 4 : M o t h e r b o a r d i n f o
C h a p t e r 4 : M o t h e r b o a r d i n f o
C h a p t e r 4 : M o t h e r b o a r d i n f o
®
XP

Advertisement

Table of Contents
loading

Table of Contents