Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for U.S. Solid JFESM00031
Summary of Contents for U.S. Solid JFESM00031
- Page 1 SEMI-AUTOMATIC STRAPPING MACHINE MANUAL NO. 9786...
-
Page 2: Table Of Contents
CONTENTS SAFETY INSTRUCTION ........1 TECHNICAL PARAMETERS ......... 5 ACCESSORY ............7 OPERATING ELEMENTS ........8 OPERATION ............9 PRECAUTIONS FOR USE ........18... -
Page 3: Safety Instruction
SAFETY INSTRUCTION Please read the instructions carefully. Not following this prompt could result in operator injury during the operation. 1. BATTERY OPERATION Environmental protection 1) Please do not burn used batteries or put them into a household trash can or waste water tank. 2) Dealers provide environment-friendly battery recycling services. - Page 4 3. OPERATION Improperly trained personnel are not allowed to operate the strapping tool. Carefully read and understand the operating instructions before using the strapping tool. If you do not follow the operating instructions or improperly load the straps, it will cause strap damage. If you are not familiar with the strapping tool, please keep your fingers far away from the squeezing or cutting areas.
- Page 5 7. BROKEN STRAP HAZARD Improper operation, excessive tensioning, or improper use of straps will loosen the tightened parts of the machine and eventually lead to straps breakdown. When this happens, the operator loses balance and falls, and the strapping tool and straps quickly fly to the operator's face. Attention: 1) If the load angle is very sharp, please add edge protection.
- Page 6 straps, and keep away from the straps loosening direction. Please use the special tool for shearing straps. Do not use a hammer, plier, hacksaw, axe, and so on. 9. FALL HAZARD Keep your work area clean and tidy. An untidy work area is likely to cause an accident.
-
Page 7: Technical Parameters
TECHNICAL PARAMETERS 1. DESCRIPTION This strapping tool uses plastic straps. Use the strap-feeding device manually to wind the plastic straps around the box (bag). Strap ends are inserted into the strapping tool and automatically tensioned and separated after friction adhesion. 2. - Page 8 4. STRAP STRENGTH Tensile strength: 400-3500N adjustable (Maximum value depends on the quality of the straps) Adhesive strength: about 75% of the plastic strap (Depending on the quality of the straps) 5. WORKING TEMPERATURE • Ambient air temperature is 5 to 45 (41℉...
-
Page 9: Accessory
ACCESSORY Please use the parts and accessories specified in the operating instructions. Using other accessories may hurt you and others. 1. BATTERY POWERED STRAPPING TOOL Some strapping tools may use NiCd (nickel-cadmium) or NiMH (nickel metal hydride) batteries; please purchase the battery for this tool according to the following parameters. -
Page 10: Operating Elements
OPERATING ELEMENTS Diode Status Indication Green Normal working Red flashing Low battery, please charge Machine failure, power off, inspect Purple Work completed... -
Page 11: Installation
OPERATION 1. INSTALLATION 1) Please do not put the strapping tools in the rain! 2) For security, the battery is not charged before delivery. 3) Please charge the battery before using it. Battery disassembly 1) Push the battery box cover assembly upward by arrow direction, and insert the battery into slot from up to down. - Page 12 Battery level Indicator 1 Indicator 2 Indicator 3 – fully Green light Green light Green light charged 1/3 - 2/3 Green light Green light Extinguish 0 - 1/3 Red light Extinguish Extinguish Extinguish Extinguish Extinguish...
- Page 13 2. OPERATION FUNCTION DESCRIPTION 1.adjustment of welding time: short press the INC key to lengthen the welding time; Short press the DEC key to shorten the welding time (each adjustment range is 0.1 seconds, and the value display range is 0.5-3.5 seconds).
- Page 14 Lock and unlock set: 1. In the state of no packaging operation, it will enter the sleep state after 120 seconds. To wake up, gently press the welding button lightly (do not press it to the bottom otherwise it will trigger the machine to perform welding operation).
-
Page 15: Operation Steps
3. OPERATION STEPS： STRAP WINDING ① Wind the straps as shown in the diagram (The strap that needs to be cut is stacked on top). This semi-electric strapping machine is installed by default with a spring that fuses the PET strapping . If you use PP strapping, please replace them with another spring we have prepared for you. - Page 16 ② STRAP INSERTION Press and hold the handle with your right hand, move the packer, put the upper and lower belts in parallel, and then release the handle. ③ STRAPS TENSIONING Hold the machine with your left hand and swing the handle back and forth with your right hand.
- Page 17 ④ CONTACT ADHESION Press the welding button and leave immediately. The packing belt is welded and the excess packing belt is cut off. After welding, the machine gives a prompt sound.
- Page 18 ⑤ REMOVE STRAPPING TOOL Press and hold the handle with your right hand to remove the machine. REMARKS: the machine will be powered off automatically after 2 minutes of unpacking operation. Press the welding button to wake up.
- Page 19 ADHESION CONTROL Normal adhesion control is necessary. You can see the quality of the adhesion with the eyes as shown in the following diagrams: Correct adhesion: Weld the entire width of the strap; the welding length is about 19 mm. A small amount of molten plastic is allowed to overflow the edge.
-
Page 20: Precautions For Use
PRECAUTIONS FOR USE 1. When tightening the machine for use, please ensure you use a strap that matches the spring installed in the machine. This electric strapping machine has a default installed spring that fuses the PET strap . If you use PP straps, please replace them with another spring we have prepared for you. - Page 21 5. If there is strap residue on the cutting gear, please clean it up in time. 6. If the machine is stuck in the strapping process (LCD in red) due to straps stuck in the machine, switch off the power, cut the straps, remove the screws on the left and right panel covers, remove the straps, and check the machine.
- Page 22 Contact Feel free to visit our website: www.ussolid.com You can also email us at: service@ussolid.com...
Need help?
Do you have a question about the JFESM00031 and is the answer not in the manual?
Questions and answers