1. Manuals
  2. Brands
  3. U.S. Solid Manuals
  4. Packaging equipment
  5. JFESM00023
  6. Manual

U.S. Solid JFESM00023 Manual

Electric strapping machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ELECTRIC STRAPPING MACHINE
MANUAL NO. 8745

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JFESM00023 and is the answer not in the manual?

Questions and answers

Related Manuals for U.S. Solid JFESM00023

Summary of Contents for U.S. Solid JFESM00023

  • Page 1 ELECTRIC STRAPPING MACHINE MANUAL NO. 8745...

  • Page 2: Table Of Contents

    CONTENTS SAFETY INSTRUCTION .............1 TECHNICAL PARAMETERS ..........5 ACCESSORY ..............7 OPERATING ELEMENTS ...........8 OPERATION ...............9 WORN PARTS REPLACEMENT ........17 COMMON FAULTS ............19...

  • Page 3: Safety Instruction

    SAFETY INSTRUCTION Please review these instructions carefully. Failure to follow them could lead to operator injury during operation. 1. Battery operation Environmental protection: 1) Do not dispose of used batteries in household trash cans, wastewater tanks, or by burning them. Short circuit 1) Do not store batteries and other metal objects together.
  • Page 4 3. Operation Personnel who are not properly trained are not allowed to operate the strapping tool. Before tightening straps, read and understand the operating instructions thoroughly. Failure to follow these instructions or improperly loading the straps could result in damage to the straps. Please ensure your fingers are kept away from any areas where squeezing or cutting could occur.
  • Page 5 6. Straps warning Do not use straps to drag or lift loads, as this can easily lead to personal injury. 7. Straps broken hazard Improper operation, excessive tensioning, or misuse of straps can result in loss of tightening force or breakage of the straps. The following hazardous situations could potentially occur: The operator could lose balance and fall.
  • Page 6 8. Tensioning straps shearing When shearing straps, please use an appropriate shearing tool and maintain a safe distance from others. Do not stand in line with the straps and stay clear of the direction in which the straps may loosen. Use a specialized tool specifically designed for shearing straps.

  • Page 7: Technical Parameters

    TECHNICAL PARAMETERS 1. Description The manufactured strapping tool uses plastic straps. Manually use the strap feeding device to wind the plastic straps around the box (bag). The end of the strap is inserted into the strapping tool and is automatically tensioned, separating after friction adhesion. 2.
  • Page 8 4. Straps strength Tensile strength: 400-3500N adjustable. (Maximum value depends on the quality of straps.) Tensioning speed: 180mm/s Adhesive strength: about 75%of plastic straps. (Depending on the quality of straps) 5. Working temperature Ambient air temperature is 41℉— 113℉. Optimum working temperature is 59℉ — 68℉.

  • Page 9: Accessory

    ACCESSORY Please use the parts and accessories that mentioned in the operating instructions. To use other accessories may hurt you and others. 1. Battery powered strapping tool As some strapping tools may use NiCd (nickel cadmium) or NiMH (nickel metal hydride) batteries, please purchase the battery for this tool according to the following parameters.

  • Page 10: Operating Elements

    OPERATING ELEMENTS Red button 1 is tensioning Red button 2 is welding button. button.

  • Page 11: Operation

    OPERATION 1. Installation 1) Please do not put the strapping tools in the rain! 2) For security, the battery is not charged when delivery. 3) Before using, please charge. Insert the battery: 1) Push the battery box cover assembly upward by arrow direction, and insert the battery into slot from up to down.
  • Page 12 2. Operation function description: After unlocking, briefly press the operation mode switch area interface to cycle through three modes (automatic, semi-automatic, and manual). 3. Tensioning force adjustment: After unlocking, briefly press the Tensioning gear selection area to display the Tensioning force adjustment interface . Press increase the tension gear value, and to decrease the tension gear value.
  • Page 13 5. Normal mode and flexible mode selection: After unlocking, briefly press the area interface to switch between normal and flexible modes. The normal mode is suitable for PET belt packaging, while the flexible mode is ideal for PP belt packaging. 6.Lock settings: ①...
  • Page 14 7.Operational process descriptions ： ①：Straps winding： Wind the straps as shown in the figure. Warning! Keep away from oil, grease and other dirt when welding plastic straps. Dirty straps can't be welded. ②. Straps inserting Lift the handle with your right hand, insert straps with left hand stack the two pieces horizontally, release the handle.

  • Page 15: Full Automatic Mode

    ③.Operational descriptions of various modes: Full automatic mode : Short press the tension button, and the belt will be automatically tightened. After reaching the set tension value, it will be automatically welded and cut. Semi automatic mode :Press and hold the tension button until the predetermined tension value is reached, then the machine will automatically weld and cut the tape.
  • Page 16 Manual mode : Press the tensioning button and hold until the straps reach the desired tension strength, then release the switch knob. Note: Keep pressing the tensioning button until the LED display turns purple. The tightening protection will not affect the next step.
  • Page 17 ④. Remove strapping tool Lift the handle and loosen the straps, then pull the machine to the right side and away from the straps. If the strapping machine is stuck and not moving, you must first remove the battery, then cut the strapping strap. Afterward, remove the panel screws and then take out the strapping strap.
  • Page 18 Welding time is too long: Such as if welding time is too long, straps are overheated, molten plastic overfiow two sides. Adhesion effect is affected. WARNING! Straps with not enough adhesive strength must be removed. Adjust the welding time.

  • Page 19: Worn Parts Replacement

    WORN PARTS REPLACEMENT Every time maintenance, please remove the battery. Cutter: first remove the left shield screw and remove it. Then remove the screw on the cutter and remove il. Take out the cutter, Keep the cutter spring; install in reverse order. Welding tooth plate: remove the fixing screw of the fusion lower tooth plate to remove the fusion lower tooth plate;...

  • Page 21: Common Faults

    COMMON FAULTS 1. Special reason: If the machine stuck in strapping process, which results straps stuck in the machine and can't be removed. Immediately cut off power, cut the straps, remove the screws on the left and right panel covers and move, remove the straps, and check the machine.
  • Page 22 -E1.1: Tensioning microswitch faliure -E1.2: Welding microswitch fault -E1.3: Rewind switch malfunction -E1.4: Reset switch failure If the above fault display appears, you can press any key to eliminate it and enter standby mode. If it cannot be restored to normal, please contact us for resolution.
  • Page 23 Contact Feel free to visit our website: www.ussolid.com You can also email us at: service@ussolid.com...

Table of Contents