Advertisement
Quick Links
FEEDER CUBE ®
FC-119H
OIL RESISTANT MODEL
IMPORTANT: APPLICATION NOTE
Input: 240 VAC, 50/60 HZ.
(Operating range 180-265 VAC)
Triple Unit Fuse Sizes:
Unit A 5A, Unit B 15A, Unit C 5A
Output: 0-240 VAC
Units A/C: 100% Duty Cycle 0.6-4A, 80% for 5A
Unit B: 100% Duty Cycle 0.6-12A, 80% for 13-15A
Circuit Boards P/N 24-491 & 24-211
Unit A Information: This unit is based on the FC-90
this unit, refer to the enclosed Adjustments and Set Up pages. Unit A is interlocked (subordinate) to the operation of Unit
B so that Unit A operates only when Unit B is feeding parts.
Unit B Information: This unit is based on the FC-90
output can be controlled with an optional part sensor. For more information on this unit, refer to the enclosed Adjustments
and Set Up pages.
Unit C Information: This unit is based on the FC-40
to the enclosed Adjustments and Set Up pages. The Unit C operation is independent of the other units.
© 2000, 2018 RODIX
RODIX INCORPORATED
TOLL FREE (800) 562-1868, FAX (815) 316-4701
E-mail custserve@rodix.com
Plus
, P/N 121-000-8775
.
INC
rodix.com
Plus
Series Part Sensing Feeder Cube®. For more information on
Plus
Series Part Sensing Feeder Cube®. The On/Off operation of the
Plus
Series Feeder Cube®. For more information on this unit, refer
File No. E183233
FC-119H.docx 2/19/2018 Page 1
Advertisement
Related Manuals for Rodix FEEDER CUBE Plus FC-119H
Summary of Contents for Rodix FEEDER CUBE Plus FC-119H
- Page 1 Unit C Information: This unit is based on the FC-40 Series Feeder Cube®. For more information on this unit, refer to the enclosed Adjustments and Set Up pages. The Unit C operation is independent of the other units. © 2000, 2018 RODIX FC-119H.docx 2/19/2018 Page 1...
- Page 2 RUN JUMPER INPUT FEEDER BOWL/HOPPER LOW VOLTAGE INPUT RODIX INC. INTERLOCK SWITCHING P/N 24-490/24-491 FC-90 PLUS SERIES TB2, OUTPUT FEEDER CUBE (DC Voltage from PLC) LOW CURRENT SWITCH FC-90 Plus Series 5-30 VDC INPUT VOLTAGE OFF/ON CONTROL WIRING DIAGRAM ...
- Page 3 R3. R3 is located on the circuit maintain a constant part feed rate. linear pot taper for the Main Control Dial, see the “S1 board near TB2-8. Programming Chart.” © 2000, 2018 RODIX FC-90 Plus Set Up J.docx 2/21/2018 Page 3...
- Page 4 B. CHOOSE A LOCATION for mounting the sensor Plus A. 4-20mA signal from a PLC can be used to remotely can be connected to a Rodix FC-40 Series on the feeder that is smooth and that will allow the Plus vary the output of the control instead of the Main (TB2-11 &...
- Page 5 OUT of warranty service, please ship it prepaid to: Rodix Inc., ATTN: Repair Department packaging. Remove the liner from the adhesive Included features: Constant On, High/Low Track level If under warranty, Rodix will repair or replace your control backing. Avoid touching the tape. Align the control, 60 pulse polarity reversal, low pulse rate, at no charge;...
- Page 6 "Parts Sensing Feeder Bowl Control" such as an available for use on applications requiring a three Plus FC-90 wire DC sensor, an interlock output, or a Constant Feed Rate (vibration feedback) sensor. FC-40 Plus Set Up.doc 2/21/2018 Page 6 © 2000, 2017 RODIX...
- Page 7 ON and OFF. Move jumper "J1" from terminal If under warranty, Rodix will repair or replace your control pots. See the S1 Switch Programming Chart. For 7, to terminal 5, (6 remains the same). Then at no charge;...
- Page 8 Rodix controls have been designed with a AUX output. The shield “drain” wire high degree of immunity to electrical should be tied to the chassis in the Rodix RECTIFIER noise; however, depending on the control RELAY DIODE control. The drain wire should be kept...
Need help?
Do you have a question about the FEEDER CUBE Plus FC-119H and is the answer not in the manual?
Questions and answers