Advertisement
Quick Links
RODIX INC.
FEEDER CUBE
VF Series
Wiring Diagram
RUN JUMPER INPUT
B)
FEEDER BOWL/HOPPER
INTERLOCK
Master VF Control TB2, Aux. OUTPUT
A)
LOW CURRENT SWITCH
+
S
-
+
Enable Input
VF Control TB2
Subordinate VF Control TB2, Ena ble INPUT
TB1
INPUT POWER
INPUT
85 - 264 VAC
Bl #14
L1
L1
L2
Bl #14
L2
Chassis
Gr/Yl #14
GND
Bl #14
-
Out +
Bl #14
+
Out -
OUTPUT POWER
OUTPUT
TB3
C)
LOW VOLTAGE INPUT
SWITCHING
(Remove Run Jumper and
-
apply DC Voltage from PLC)
+
S
5-30 VDC INPUT VOLTAGE OFF/ON
CONTROL
+
+
S
S
-
Enable Input
VF Control TB2
DANGER! SHOCK HAZARD
FUSE
FUSE
Master Control
Bowl/Hopper
Interlock Output
-
-
1
TB5
High Voltage LED
Keypad
R27
TB4
N.O. RELAY
Aux Out
SENSOR
-
-
-
+
+
S
S
-
+
Br
Wh
Bu
ACCEPTS BOTH OPTIC AND PROX SENSORS, NPN OR PNP.
CONNECT SINK OR SOURCE WIRE TO "SIG" INPUT
LCD Display
TB6
P1
LC D C ontras t
R21
Enable
V
mA
Accel
TB2
-
-
+
+
S
S
S
Br
CFR Sensor
Bu
RUN
P/N 123-215
JUMPER
OPTICS
+
BANNER
SIG
SM312FP1H
OPTIC SENSOR
-
P/N 111-500
SENSOR OPTION
Page 1
9/18/2013
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Rodix FEEDER CUBE VF-3CE
Summary of Contents for Rodix FEEDER CUBE VF-3CE
- Page 1 RODIX INC. FEEDER CUBE VF Series Wiring Diagram RUN JUMPER INPUT FEEDER BOWL/HOPPER LOW VOLTAGE INPUT INTERLOCK SWITCHING Master VF Control TB2, Aux. OUTPUT (Remove Run Jumper and LOW CURRENT SWITCH apply DC Voltage from PLC) 5-30 VDC INPUT VOLTAGE OFF/ON...
-
Page 2: Setup And Adjustments
VF Series FC-90 Bowl/Hopper Interlock “+” and “sig” (see TB2 on OIL RESISTANT GENERAL PURPOSE the wiring diagram) can be connected to a Rodix Mounting FC-40 All-Purpose Series control (TB2-11 & 12) The control may be mounted vertically or horizontally, when control of a bulk material hopper is needed. - Page 3 pressed for 1 minute, the display reverts to the normal 11. External Speed Control 6. External Speed Control Connections operating display mode. The feeder control’s power level can be controlled The following methods of remote power level control by an external signal from a PLC, CFR sensor, or can be utilized when desired: 7.
- Page 4 12. CFR Positive and Negative Gain the normal display menu will show a bold “F.” 18. Run Mode Settings The CFR Positive and Negative Gain settings control When”=” is shown in bold, the control is locked The “I/O Interface” menu contains the portion of the the rate the feeder’s vibration level is corrected by the menu that controls the run mode and empty bowl onto the resonate frequency of the feeder.
- Page 5 The VF Series control amplitude can be adjusted from the normal operating If under warranty, Rodix will repair or replace your control display. Press and hold “Enter” to enter the program adjusts the amplitude automatically to match the CFR at no charge;...
- Page 6 VF-3 Dimensions VF-3CE Application Note 10/23/2012 Page 6...
- Page 7 Control Menu Layout for VF-3CE, VF-9CE Normal Operation Display Press and hold ‘Enter’ to enter the program menu or get to the security menu. Use the arrow up and down keys to adjust the security number. Press enter to test the security number. Main Menu Sub Menu Adjustments...
- Page 8 Steps to Interlock Two VF Series Controls together If a PLC is interfaced to both controls, optical isolation is necessary, see step 4 below. 1. Remove the run jumper from TB2 “Enable” terminals of the subordinate control. 2. Add a wire from the “Aux Out +” terminal of the master control to the “Enable S” terminal of the subordinate control. 3.
-
Page 9: Rodix Solution
Rodix controls have been designed with a AUX output. The shield “drain” wire high degree of immunity to electrical RECTIFIER should be tied to the chassis in the Rodix noise; however, depending on the control RELAY DIODE control. The drain wire should be kept... - Page 10 R.C. or D.C. A.C. Rectified Full Wave AC Direct Current Alternating Current Half Wave Full Wave 3600 Vibrations Per Min. 7200 Vibrations Per Min. From TUV Rheinland, FAQ http://www.jpn.tuv.com/en/services/product_testing/all_types_of_products/electromagnetic_compatibility_services_emc_/emc_faq.php © RODIX Inc. 2006 E:\Eng\CE\CE restrictions for harmonic current emissions 060501.doc...
- Page 11 The amount of voltage fluctuations and flicker depends on how often the electrical load is turned On and Off by the machine and how large the load is. From TUV Rheinland, FAQ http://www.jpn.tuv.com/en/services/product_testing/all_types_of_products/electromagnetic_compatibility_services_emc_/emc_faq.php © RODIX Inc. 2006 E:\Eng\CE\CE Flicker 060511.doc...
- Page 12 195 On/Off cycles per 1 minute Unlimited On/Off cycles per 1 minute This chart is based on Rectangular voltage changes at equal intervals using the Pst=1 chart, fig. 4 of standard EN61000-3-3. Plt = Pst x 0.65 © RODIX Inc. 2006 E:\Eng\CE\CE Flicker 060511.doc...
- Page 13 Machinery Directive, 2006/42/EC, and requirements of the Low Voltage Directive, 2006/95/EC. Safety of Machinery: EN 60204-1: 2006 Machine Safety was evaluated by Rodix Inc. Supplementary Information: Electromagnetic Compatibility Record 2011-068B EMC testing was performed by: L.F.
Need help?
Do you have a question about the FEEDER CUBE VF-3CE and is the answer not in the manual?
Questions and answers