Related Manuals for Dahua Technology CS4006-4GT
Summary of Contents for Dahua Technology CS4006-4GT
- Page 1 Ethernet Switch (Cloud Managed Switch) Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO.,LTD. V1.0.1...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the installation, functions and operations of the cloud managed switch (hereinafter referred to as "the Device"). Read carefully before using the device, and keep the manual safe for future reference. Safety Instructions The following signal words might appear in the manual. - Page 3 Quick Start Guide our official website. The manual is for reference only. Slight differences might be found between the electronic version and the paper version. All designs and software are subject to change without prior written notice. Product updates ● might result in some differences appearing between the actual product and the manual.
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, and comply with the guidelines when using it. Transportation Requirements Transport the device under allowed humidity and temperature conditions. -
Page 5: Operation Requirements
Quick Start Guide Do not place the device in a place exposed to sunlight or near heat sources. ● Keep the device away from dampness, dust, and soot. ● Put the device in a well-ventilated place, and do not block its ventilation. ●... -
Page 6: Maintenance Requirements
Quick Start Guide Do not unplug the power cord on the side of the device while the adapter is powered on. ● Use the device under allowed humidity and temperature conditions. ● Do not drop or splash liquid onto the device, and make sure that there is no object filled with ●... -
Page 7: Table Of Contents
Quick Start Guide Table of Contents Foreword................................I Important Safeguards and Warnings......................III 1 Overview................................1 1.1 Introduction............................1 1.2 Features..............................1 2 Port and Indicator............................2 2.1 Front Panel............................. 2 2.1.1 Front Panel (4/8-port)........................2 2.1.2 Front Panel (16/24-port)......................3 2.2 Rear Panel...............................3 2.2.1 Rear Panel (4/8-port)........................ -
Page 8: Overview
Quick Start Guide 1 Overview 1.1 Introduction The Cloud Managed Switch is a layer-2 commercial device. With a full-metal design, the Device has great heat dissipation capabilities on its shell surface, and is able to work in environments that range from –10 °C to +55 °C (+14 °F to +131 °F). In addition, based on the DoLynk Care Cloud Server, the Device can be managed through the DoLynk Care app or webpage, the network topology diagram function can be used to quickly locate the problem. -
Page 9: Port And Indicator
Quick Start Guide 2 Port and Indicator 2.1 Front Panel 2.1.1 Front Panel (4/8-port) The following figure uses an 8-port 100 Mbps cloud managed device as an example, and might differ from the actual product. Figure 2-1 Front panel (4/8-port) Table 2-1 Description of front panel (4/8-port) Name Description... -
Page 10: Front Panel (16/24-Port)
Quick Start Guide Name Description Link/Act indicator. On: Connected to the Device. ● Link/Act indicator Off: Not connected to the Device. ● Flashing: Transmitting data. ● 2.1.2 Front Panel (16/24-port) The following figure uses a 16-port 100 Mbps cloud managed device as an example, and might differ from the actual product. -
Page 11: Rear Panel (4/8-Port)
Quick Start Guide 2.2.1 Rear Panel (4/8-port) The figures might differ from different models. Please refer to the actual product. Figure 2-3 Rear panel (4/8 port) Table 2-3 Description of rear panel (4/8 port) Name Description Connecting GND. Normal GND connection of the Device guarantees device ●... - Page 12 Quick Start Guide Name Description Connecting GND. Normal GND connection of the Device guarantees device ● Ground terminal lightning protection and anti-interference. You must connect the GND cable before powering on the Device and power off the Device before disconnecting the GND cable. The sectional area of the GND cable must be more than 2.5 ●...
-
Page 13: Installation
Quick Start Guide 3 Installation Different installation methods suit for different models. Please select appropriate methods as needed. 3.1 Preparation Select an appropriate installation method as needed. ● Install the Device on a solid and flat surface. ● Leave around 10 cm of open space around the Device for heat dissipation and to ensure good ●... - Page 14 Quick Start Guide Screws do not come with the package. Purchase them as needed. ● Make sure that the distance between the screws is the distance between the wall- ● mount holes (77.8 mm for a 4-port switch and 128.4 mm for an 8-port switch). Step 2 Align the wall-mount holes on the back cover of the Device with the screws, and hang the Device on the screws.
-
Page 15: Wiring
Quick Start Guide 4 Wiring 4.1 Connecting GND Cable Background Information Normal GND connection of the Device is the important guarantee for Device lightning protection and anti-interference. Procedure Step 1 Remove the ground screw on the Device and place it properly. Pass the ground screw through the round hole of the OT terminal of the ground cable. -
Page 16: Connecting Sfp Ethernet Port
Quick Start Guide Figure 4-2 Ethernet port pin number Figure 4-3 Pin description The cable connection of RJ-45 connector conforms to the standard 568B (1-orange white, 2-orange, 3-green white, 4-blue, 5-blue white, 6-green, 7-brown white, 8-brown). 4.4 Connecting SFP Ethernet Port When installing the SFP optical module, do not touch the gold finger of the SFP optical module. - Page 17 Quick Start Guide Figure 4-4 Install SFP module Step 4 Remove the dust cap of the LC connector of the optical fiber and the dust plug of the SFP optical module. Step 5 Connect the LC connector of the optical fiber to the SFP optical module. Figure 4-5 Connect optical fiber...
-
Page 18: Usage Mode
Quick Start Guide 5 Usage Mode 5.1 Managing the Device by Cloud Management The Cloud Managed Switch supports device management through the DoLynk Care app and webpage. 5.1.1 Managing the Device by DoLynk Care App Prerequisites Make sure that the Device is connected to the power and the network before adding the Device. ●... -
Page 19: Managing The Device By Dolynk Care Webpage
Quick Start Guide Figure 5-2 Add the device 2. You can scan the QR code to obtain the SN or tap to manually enter the SN. When adding the Device through the SN, you need to enter the SN and password. The default password before device initialization is the SC code which can be obtained from the label on the Device. -
Page 20: Managing The Device By Local Webpage
Quick Start Guide When adding the Device through the SN, you need to enter the SN and password. ● The default password before device initialization is the SC code which can be obtained from the labeling on the Device. You cannot add the Device which has been bound to an account. ●... -
Page 21: Login The Device
Quick Start Guide 5.2.2 Login the Device Prerequisites The Device has been initialized. ● Make sure that the Device is connected to the computer, and the IP addresses of the computer ● and the device are on the same network segment. Procedure Step 1 Open the browser, enter the IP address of the Device in the address bar, and then press... -
Page 22: Appendix 1 Security Commitment And Recommendation
Quick Start Guide Appendix 1 Security Commitment and Recommendation Dahua Vision Technology Co., Ltd. (hereinafter referred to as "Dahua") attaches great importance to cybersecurity and privacy protection, and continues to invest special funds to comprehensively improve the security awareness and capabilities of Dahua employees and provide adequate security for products. -
Page 23: Service Configuration
Quick Start Guide Service Configuration 1. Enable HTTPS It is recommended that you enable HTTPS to access Web services through secure channels. 2. Encrypted transmission of audio and video If your audio and video data contents are very important or sensitive, we recommend you to use encrypted transmission function in order to reduce the risk of your audio and video data being eavesdropped during transmission. -
Page 24: Software Security
Quick Start Guide By viewing logs, you can learn about the IP addresses that attempt to log in to the device and key operations of the logged users. 3. Configure network log Due to the limited storage capacity of devices, the stored log is limited. If you need to save the log for a long time, it is recommended to enable the network log function to ensure that the critical logs are synchronized to the network log server for tracing.
Need help?
Do you have a question about the CS4006-4GT and is the answer not in the manual?
Questions and answers