Related Manuals for Dahua Technology DH-PFS5936-24GF8GT4XF
Summary of Contents for Dahua Technology DH-PFS5936-24GF8GT4XF
- Page 1 Dahua 36-Port Managed Gigabit L3 Switch Quick Start Guide V1.0.0 ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD.
-
Page 2: Foreword
General This manual introduces the functions and operations of 36-port managed Gigabit L3 switch (hereinafter referred to as "the Device"). Model DH-PFS5936-24GF8GT4XF Safety Instructions The following categorized signal words with defined meaning might appear in the Guide. Signal Words Meaning... - Page 3 About the Manual The manual is for reference only. If there is inconsistency between the manual and the actual product, the actual product shall prevail. We are not liable for any loss caused by the operations that do not comply with the manual. ...
-
Page 4: Table Of Contents
Table of Contents Foreword ..............................I 1 Overview ..............................1 Product Introduction ........................1 Front Panel ............................ 1 Rear Panel ............................ 1 Indicator Description ........................2 2 Installing the Device ..........................3 Installing the Switch ........................3 2.1.1 Installing the Switch on the 19-inch Standard Rack ............3 2.1.2 Installing the Switch on the Working Desk ................. -
Page 5: Overview
The 36-Port Managed Gigabit L3 Switch has the following model: Table 1-1 Model Name Model 36-Port Managed Gigabit L3 Switch with 24×100/1000Mbps DH-PFS5936-24GF8GT4XF SFP Ports, 8× Gigabit Ports and 4× 1G/10G SFP+ Front Panel See Figure 1-1 for the front panel of the switch. Figure 1-1... -
Page 6: Indicator Description
Figure 1-2 Rear panel Table 1-3 Rear panel description Description GND screw AC power port Indicator Description Table 1-4 Indicator description Indicator Status Description The switch is powered on and the power ON (green light) module is working properly. The switch is not powered on or the power module is not working properly. -
Page 7: Installing The Device
Installing the Device The switch can be installed on the 19-inch standard rack, and it can also be directly placed on the working desk. To avoid damage to the device or human, follow the attentions: Do not place the switch near water and keep away from humid environment to avoid water ... -
Page 8: Installing The Switch On The Working Desk
Figure 2-2 Installing the switch The rackmount hangers are not for sustaining the weight of the switch, and they are for fixing the switch. The carrier is necessary for sustaining the switch. 2.1.2 Installing the Switch on the Working Desk You can place the switch on the clean, stable, and grounded working desk. -
Page 9: Connecting The Gnd Cable
To connect the configuration cable, do the following: Step 1 Connect the DB-9 plug of the configuration cable to the serial port of the PC. Step 2 Connect the RJ-45 port of the configuration cable to the Console port of the switch. 2.2.2 Connecting the GND Cable The GND cable is not supplied, and you need to purchase it by yourself. -
Page 10: Installing Sfp Module And Connecting The Optical Fiber
2.2.4 Installing SFP Module and Connecting the Optical Fiber WARNING Do not touch the golden finger of the SFP module when installing the SFP module. Do not pull out the dustproof plug of the SFP module before connecting the optical fiber. Do not directly insert the SFP module connected with the optical fiber into the SFP slot. -
Page 11: Logging In The Device
Logging in the Device The default IP address of the switch is 192.168.1.110. You can only log in the device by Console port for first time login. The user name and the password are both “admin”, and the baud rate of the serial port is 115200. You can view the actual IP address through show ip interface command line. - Page 12 Figure 3-1 VLAN networking Configuration Procedure To configure the switch, do the following: Step 1 Create the VLAN. SWITCH #configure terminal SWITCH (config)#vlan 2 SWITCH (config-vlan)# exit SWITCH (config)#vlan 3 SWITCH (config-vlan)# exit Step 2 Allocate the ports into the VLAN. SWITCH(config)# interface GigabitEthernet 1/1 SWITCH (config-if)# switchport access vlan 2 SWITCH (config-if)# exit...
-
Page 13: Appendix 1 Cybersecurity Recommendations
Appendix 1 Cybersecurity Recommendations Cybersecurity is more than just a buzzword: it’s something that pertains to every device that is connected to the internet. IP video surveillance is not immune to cyber risks, but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks. - Page 14 Change Default HTTP and Other Service Ports We suggest you to change default HTTP and other service ports into any set of numbers between 1024~65535, reducing the risk of outsiders being able to guess which ports you are using. Enable HTTPS We suggest you to enable HTTPS, so that you visit Web service through a secure communication channel.
- Page 15 The network should be partitioned and isolated according to the actual network needs. If there are no communication requirements between two sub networks, it is suggested to use VLAN, network GAP and other technologies to partition the network, so as to achieve the network isolation effect. ...
- Page 16 ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. Address: No.1199, Bin'an Road, Binjiang District, Hangzhou, P.R. China Postcode: 310053 Tel: +86-571-87688883 Fax: +86-571-87688815 Email: overseas@dahuatech.com Website: www.dahuasecurity.com...