Related Manuals for Snorkel S3006P
Summary of Contents for Snorkel S3006P
- Page 1 OPERATORS MANUAL S3006P sn: 01-****00138+ Part Number 514690-001-EN-A S3008P sn: 01-****00473+ July 2023 S3010P sn: 01-****03836+ Original Instructions S3210P sn: 01-****00001+...
- Page 2 The aerial platform is not electrically insulated. Death or serious injury will result from contact with, or inadequate clearance from, an energized conductor. Do not go closer than the minimum safe approach distance as defined by the Minimum Safe Approach Distance section in Chapter 3–Safety. Regard all conductors as energized.
-
Page 3: Table Of Contents
Tilt Alarm ..............12 Chapter 2 – Specifications Chapter 5 – Gauges and Displays Component Identification ..........3 Battery Charge Indicator ..........13 General Specifications – S3006P .......4 Battery Condition LED ..........13 Aerial Platform ............4 Platform ..............4 Chapter 6 – Batteries Function Speed ............4 General Maintenance ..........15... - Page 4 Table of Contents Flashing Lights ............25 Battery Condition LED ..........25 Placards and Decals..........27 Prestart Inspection Checklist ........29 Chapter 9 – Operation Preparing for Operation ..........31 Lower Controls ............31 Upper Controls ............32 Platform ..............32 Raising and Lowering ..........32 Lowering Interrupt ..........32 Pull-Out Tray.............32 Chapter 10 –...
-
Page 5: Chapter 1 - Introduction
Additional copies of this manual may be ordered from information in this manual and on the placards and Snorkel. Supply the model and manual part number from the front cover to assure that the correct manual will be decals on the machine before operating the aerial supplied. -
Page 6: Maintenance
Owners, Users, Operators, Lessors and Lessees of ANSI/ scope of the machine specifications. SIA A92.3 Manually Propelled Elevating Work Platforms” is available from Snorkel dealers or from the factory upon The operator bears ultimate responsibility for following request. all manufacturer’s instructions and warnings, regulations... -
Page 7: Chapter 2 - Specifications
Guardrails Manual Toeboards Component Tray Scissors Structure Hydraulic Reservoir / Pump Batteries Safety Prop One on Each Side Forklift Pocket Chassis Forklift Pocket Lower Controls Brake Lever Battery Charge Indicator Right Side Emergency Lowering Lever Nameplate Rear 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 8: General Specifications - S3006P
Chapter 2 – Specifications General Specifications - S3006P Aerial Platform Electrical System Working height 12.9ft (3.96m) Voltage 12 V DC negative chassis ground Maximum platform height 6.4ft (1.96m) Source One - 12 V 105 amp hour battery Wheelbase 3ft (1m) -
Page 9: General Specifications - S3008P
Lift Level Sensor Interlock Sound Pressure Level Side-to-side 1.5 degrees At work station below 70 dB(A) Front-to-rear 2 degrees Vibration Whole body vibration < 0.5 m/sec² Tires Nonmarking solid rubber Hand / Arm vibration < 2.5 m/sec² 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 10: General Specifications - S3010P / S3210P
Platform lower 10 to14 seconds At work station below 70 dB(A) Lift Level Sensor Interlock Vibration Whole body vibration < 0.5 m/sec² Side-to-side Hand / Arm vibration < 2.5 m/sec² Front-to-rear 2 degrees Tires Nonmarking solid rubber 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 11: Chapter 3 - Safety
Over 200kV to 350Kv 6.10 Over 350kV to 500kV 7.62 Over 500kV to 750kV 10.67 Over 750kV to 1000kV 13.72 Table 1 – Minimum Safe Approach Distance Denotes prohibited zone Figure 3 – Minimum Safe Approach Distance 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 12: Prestart Inspection
Make sure there is sufficient clearance around the machine before moving the chassis or platform. Allow sufficient room and time 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 13: Electrical System
If acid contacts your eyes, flush immediately with clear unless the application is approved in writing by Snorkel. water and get medical attention. Do not use the aerial platform as a crane, hoist, jack or... - Page 14 Chapter 3 – Safety 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P...
-
Page 15: Chapter 4 - Safety Devices
At the upper controls, the emergency stop is a two- position red push button (refer to Figure 4.2). 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 16: Lift Level Sensor Interlock
Figure 4.5 – Guard Rails On S3006P, S3008P, S3010P machines the lowering le- ver is at the rear of the aerial platform (refer to Figure 4.3). The entry gate allows for access to the platform. The gate must be closed except when personnel are entering or leaving the platform. -
Page 17: Chapter 5 - Gauges And Displays
40% to 20% Fast flash 20% to 10% Steady on less than 10% Note: To maximise battery life always recharge the battery after use and never store the machine for extended periods without first fully recharging the bat- tery. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... - Page 18 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P...
-
Page 19: Chapter 6 - Batteries
Inlet (refer to Figure 6.1) using a 3 conductor, 1.5 mm (12 gauge) or larger extension cord. The exten- The S3006P, S3008P, S3010P series has a built in feature sion cord must be as short as possible and in good whereby power is cut to the machine when the battery electrical condition. - Page 20 6 mm (¼″) of the bottom of the filler neck inside each hole. If needed, add distilled water. 11. Tightly replace the caps on the battery and close and latch the component tray. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P...
-
Page 21: Chapter 7 - Controls
• Press and hold the platform raise button to raise the 7. Platform lower button platform. 8. Control selector switch 9. Power LED • Press and hold the platform lower button to lower the platform. • An alarm will sound as the platform lowers. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 22: Upper Controls
This switch is spring returned to the off position. Press and hold the interlock button inward continually to operate the machine from the upper controls. Platform Raise/Lower Buttons The platform raise/lower buttons are used to raise or 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 23: Chapter 8 - Prestart Inspection
Electrical power is supplied from one 105 amp hour, charging. 12 volt battery. The battery supplys 12 volt DC electrical power to operate the aerial platform drive and control system. The battery is in the pull-out tray on the right side of the aerial platform. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 24: Battery Terminals
Properly position the safety prop before reaching through the scissors structure. Figure 8.5 – Safety Props 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 25: Cables And Wiring Harness
4. Make sure all hoses and tubes are held firmly in their support brackets. 5. Check under the chassis for fluid that has leaked. Hydraulic fluid leaks are easily visible on the ground. Figure 8.6 – Hydraulic Tray 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 26: Casters/Tires
2. Lower the platform and make sure the alarm sounds. 1. Pull the emergency stop button outward (refer to Figure 8.10). 2. Insert the key into the control selector switch and turn the switch to the lower controls position. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 27: Emergency Lowering System
• Push downward on the lever to lower the platform. 4. Make certain the lever/handle is fully released and the emergency lowering valve is fully closed before operating the aerial platform. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 28: Fasteners
1. Visually inspect all components of the guardrail properly. Do not operate the machine until the prob- system. Make sure the rails and toeboards are all in lem is corrected. place and free of any damage or deformation. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 29: Lowering Interupt
2. Operate any control function and visually check to see that the light is flashing approximately one flash Placard and decal kits are available from Snorkel. per second. The safety related placards and decals are illustrated on Note the following pages. - Page 30 Chapter 8 – Prestart Inspection 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P...
- Page 31 Any weight added must be distributed equally on each axle. Axle weights with machine in the stowed position. STEER AXLE DRIVE AXLE 0070901 Drawer must be closed when platform is elevated. 514194-000 514194-000 S3006P PN 514043-000 501453-000 S3008P PN 514044-000 Right Side 514043-000 S3010P PN 514045-000 0083426 514043-000 0083426...
- Page 32 To continue lowering release the controls, wait for 3 seconds and re-select lowering controls, the platform will then start to lower after a further 1.5 seconds delay. 514656-000 514656-000 Left Side 501453-000 SAFTE Y AND OPER ATING INFORM ATION INSIDE KEEP COVER CLOSED AND LATCHED 0073043 0073043 Front 300700 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P...
-
Page 33: Prestart Inspection Checklist
Proper operation/ raise and lower Emergency stop Shuts off upper controls Lowering alarm Sounds when platform lowers Lowering delay Proper operation, limit switch delays lowering Battery condition indicator Proper operation Placards and Decals In place and readable 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... - Page 34 Chapter 8 – Prestart Inspection 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P...
-
Page 35: Chapter 9 - Operation
Preparing for Operation Use the following procedure to prepare the aerial platform for operation: 1. Perform a prestart inspection (refer to Chapter 8). 2. Close and latch the battery and component tray. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 36: Upper Controls
• To raise the platform, press and hold the platform raise button until the desired height is reached. • To lower the platform, press and hold the platform lower button until the desired height is reached. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 37: Chapter 10 - Stowing And Transporting
2. Engage the brakes on both of the rear wheels. 3. Remove all personnel, tools, materials, or other loose objects from the platform. 4. Insert the forklift forks into the pockets on either side of the machine.(refer to Figure 10.1). 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... -
Page 38: Hoisting
(refer to Figures 10.4). Have any damage repaired by a qualified service technician before attempting 3. Position the aerial platform on the tail lift. to hoist the machine. 4. Engage the brakes on both of the rear wheels. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... - Page 39 6. Use chains or straps to securely fasten the aerial platform to the transport vehicle using the straps through the fork lift pockets. Proper tie-down and hauling is the responsibility of the carrier. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P...
- Page 40 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P...
-
Page 41: Chapter 11 - Emergency Operation
4. While standing clear of the scissors structure, engage the control. The platform will begin to lower as the lever is pushed down. 5. Release the lever to stop the platform from lowering. 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P... - Page 42 Chapter 11 – Emergency Operation 514690-001-EN-A - S3006P,S3008P,S3010P,S3210P...
-
Page 43: Chapter 12 - Troubleshooting
S3006P and 5.1’ (1.6m) for S3010P. than 4.5’ (1.4 m) for S3008P, 3.2’ (1m) for S3006P and 5.1’ (1.6m) for S3010P. Battery charger does not indi- No source of power. Make sure power source is plugged in cate a reading when charging and turned on. -
Page 44: Appendix A - Glossary
This system includes a harness or belt, lanyard, daily before operating the aerial platform. and a lanyard anchor. Federal OSHA, ANSI, and Snorkel require the use of additional fall protection beyond the platform guardrails on boom supported qualified person –... - Page 47 All parts returning should be still in a factory state, free of any alteration to the original design. If the parts are subject to repair it will need to be pre authorized by the Snorkel Product Sup- port Group and or Warranty Department prior to the repair being completed.
- Page 48 10. Reimbursement policy, labor will be paid at 75% of posted hourly shop rate. Travel time will be paid at $50 per hour up to a maximum of 3 hours. Snorkel will pay 1 hour of troubleshooting time per warranty claim, un- less expressly agreed otherwise in writing and in advance by Snorkel’s Warranty Department.
- Page 49 Maintenance, and repair Parts Manuals. 4. Normal wear of any Snorkel component part(s). Normal wear of component parts may vary with the type, ap- plication or type of environment in which the machine may be used; such as, but not limited to sandblasting applications.
- Page 50 Distributor/SSC/Dealer. Warranty support should be from the Distributor/SSC/Dealer from whom the Snorkel product was purchased. Where Snorkel equipment is supplied directly from the factory the end customer, or if unable to contact the Distributor/SSC/Dealer, may contact the Snorkel Warranty Department for further assistance.
-
Page 51: Manufacturer's Address
Manufacturer’s Address Snorkel Europe Ltd Vigo Centre, Birtley Road, Washington, Tyne & Wear, NE38 9DA, UK... - Page 52 Local Distributor / Lokaler Vertiebshändler / Distributeur local El Distribuidor local / ll Distributore locale EUROPE, MIDDLE EAST AFRICA & ASIA PHONE: +44 (0) 845 1550 058 FAX: +44 (0) 845 1557 756 NORTH & SOUTH AMERICA PHONE: +1 785 989 3000 TOLL FREE: +1 800 255 0317 FAX: +1 785 989 3070 AUSTRALIA...
Need help?
Do you have a question about the S3006P and is the answer not in the manual?
Questions and answers