Advertisement
Quick Links
7' Turbo Tube Slide
Note: This accessory is designed to fit a 7' Deck height only.
C A U T I O N
•
Do not climb on the
outside of the slide
• This slide is designed for
home use only, not for
Public Playgrounds
• Product intended for
children ages from 2-10
years old.
WARNING:
!
Assembly by an adult.
PLEASE READ BEFORE BEGINNING ASSEMBLY!!
Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing
DO NOT RETURN
anything, please
To register your product and download unit specific Turbo Tube Slide instructions, visit:
Other benefits include information on product warranties, assembly plan updates, joining our mailing
list for new products and promotions, and providing feedback on products.
ASSEMbly INSTRUCTIONS
IMPORTANT!!
Service Department at the number below.
http://www.swing-n-slide.com
Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545
Visit our web site at: www.swing-n-slide.com or call us at
1-800-888-1232
to the store where purchased. Please call our Customer
Advertisement
Related Manuals for Playcore Swing-N-Slide 7' Turbo Tube Slide
Summary of Contents for Playcore Swing-N-Slide 7' Turbo Tube Slide
- Page 1 ASSEMbly INSTRUCTIONS 7' Turbo Tube Slide Note: This accessory is designed to fit a 7’ Deck height only. C A U T I O N • Do not climb on the outside of the slide • This slide is designed for home use only, not for Public Playgrounds •...
- Page 2 Turbo Tube Slide Dimensions 63-7/16'' 58-11/16'' 34-3/4''...
- Page 3 Proper Placement of Turbo Tube Slide on The Tower Option 3 Swing beam Safety Zone Tower Deck Swing beam Option 2 Swing beam Safety Zone Option 1 NOTE: This diagram is based on a 47-1/2’’ square deck.
- Page 4 Safety Checklist for Swing-N-Slide ccessories Observing the following statements and warnings reduces the likelihood of serious or fatal injury Installation Safety – Have You: Consulted the assembly instructions supplied with your particular model? Do not alter its design or add/remove components. Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.) Using a hacksaw, cut off all protruding threaded ends of bolts and other fasteners and remove any sharp edges with a metal file as needed, and coated fastener ends with lead free paint?
-
Page 5: Hardware Included
TOOLS REQUIRE CIRCUlAR SAW DRIll 1/2" SOCKET & WRENCH TAPE MEASURE WRENCH SAFETy GlASSES 1/8" DRIll bIT SQUARE PHIllIPS bIT & DUST MASK HARDWARE INClUDED (12) 5/16'' x 1-1/2'' Lag Bolts (95) 5/16'' x 3/4" Hex Head Bolts (214) 5/16'' Flat Washers (2) 5/16'' x 2-3/4'' Bolts (101) 5/16'' loc nuts (4) 5/16'' x 1'' Bolts... -
Page 6: Slide Components
SlIDE COMPONENTS (1) Slide Bracket (1) Entrance Section marked no. 1 (1) Entrance Panel (1) Support Bracket (1) Entrance Section marked no.2 (1) Exit Section marked no. 5 (2) 90 Sections w/flange, marked no. 4 (3) 90 Sections w/o flange, marked no. 3 (1) Slide Base marked no. - Page 7 ssembly Instructions EntrancE SEction, 90° SEction (2) Fig. 1 and Exit SEction notES: • At least two individuals are needed to assemble the Turbo Tube Slide. • To aid in aligning holes when assembling sections, insert a screwdriver through adjacent holes to maintain hole alignment.
- Page 8 ssembly Instructions Mounting PanEl Fig. 4 1. Position the mounting panel as indicated in (Fig. 4) (The stamped "T" should be at the top). The panel should be placed to the opening so all the bolt holes fully expose a wood surface except those identified with arrows (which should be clear of any wood surface).
- Page 9 ssembly Instructions tubE aSSEMbly Fig. 7 1. Position the 90 section to the entrance section so Rotate seam the seams line up. Rotate the section two holes two holes to to the right (clockwise) and realign with the holes the right (clockwise) of the entrance section (see Fig.
- Page 10 ssembly Instructions tubE aSSEMbly (cont.) Fig. 9 Position the exit section to the previously attached sections so the seams line up. Rotate the section two holes to the left (counterclockwise) and realign with the holes of the entrance section (see Fig. Insert a 3/4"...
- Page 11 ssembly Instructions Mounting SlidE Fig. 11 2-3/4" bolt The help of at least one other individual will be required for mounting the slide. 2-3/4" bolt washer Insert the 2-3/4" bolts through a washer, through previously drilled 3/8" holes in the washer upper rail of the unit (see Fig.
- Page 12 ssembly Instructions SuPPort and brackEt aSSEMbly Fig. 13 1. Position the slide bracket between the slide and activity center (Fig. 13). Remove appropriate bolts from the slide (the fourth and fifth bolts as indicated), Attach bracket to the underside of the seam using the previously removed hardware exit section (Fig.
- Page 13 Addendum to Page 10 Fig. 8 To show configuration when creating a 9 ft slide (7 ft slide plus one extra section)
Need help?
Do you have a question about the Swing-N-Slide 7' Turbo Tube Slide and is the answer not in the manual?
Questions and answers