Download Print this page

Inel YYGL Series Installation And Use Instructions And Warnings

Advertisement

Quick Links

Installation and use instructions for drive types: YYGL and GM
The drive with mechanical end stops is available in eleven versions:
YYGL35S-6/28,GM35S-6/28 (N-6)
YYGL35SH-6/17,GM35SH-6/17 (N-6SH)
YGL35S-10/17, GM35S-10/17 (N-10)
YYGL35S-13/14, GM35-13/14 (N-13)
YYGL45S-20/15, GM45S-20/15 (N-20)
YYGL45M-20/15, GM45M-20/15 (N-20NHK)
YYGL45S-40/15, GM45S-40/15 (N-40)
YYGL45M-50/12, GM45M-50/11 (N-50NHK)
YYGL59S-100/12 (N-100)
YYGL59M-100/12 (N-100NHK)
YYGL59M-140/9 (N-140NHK)
1. Safety instructions
1.1 Basic guidelines
The standard drive is handed over in a condition for safe installation
and operation, provided that all the instructions in the operating
manual and the valid valid safety regulations have been observed
and accident prevention regulations. Only qualified and authorised
persons should work on the installation and repair of electrical
equipment. Alterations or modifications to the drive are not permitted.
Warranty repairs may only be carried out by the manufacturer. Only
original spare parts and accessories must be used for post-warranty
repairs. The operational safety of the delivered drive is only guaranteed
when used in accordance with the manufacturer's specifications. The
limit values specified in the technical data may not be exceeded under
any circumstances.
1.2 Supplementary safety provisions
Important safety and accident prevention regulations must be observed
when installing, commissioning, maintaining the drive. The following
regulations require special attention:
1. fire regulations.
2 Accident prevention provisions.
1.3 General comments on hazards and safety measures
The specified notes are general guidelines when using INEL devices
in combination with other devices. These indications must be strictly
adhered to when installing and operating the devices.
Instructions translated EN
Models:
YYGL35S, GM35S, GM35SH, YYGL35SH, YYGL45S,
GM45S, YYGL45M, GM45M, YYGL59S, YYGL59M
CAUTION - Warning of possible damage to the drive,
roller shutter, roller shutter box, façade, etc., if
appropriate precautions are not taken:
Before installing the actuator and setting the limit switches,
check the fixing of all screw connections.
Danger - means that there is a risk to the life and health
of the user if appropriate precautions are not taken:
Before switching on, it is necessary to check that the permissible
device voltage is compatible with the local supply voltage.
Observe applicable safety and accident prevention regulations.
A circuit breaker that allows safe disconnection of the power
supply (e.g. a fuse disconnector) should be used, installed so that
all connections can be easily disconnected.
Wires and cables should be checked regularly for insulation
damage and conductor continuity.
If the cables are found to be damaged, the damaged cables must
be replaced immediately after switching off the power supply.
1.4 Warning
Don't let children play with the controls.
Keep remote control devices out of the reach of children.
Watch the blind moving and keep people away until it is fully
open or closed.
Users of the roller shutter must be trained and instructed
in how to operate the roller shutter and in the dangers associated
with its use. People can be considered trained if the employer,
administrator or owner has allowed them to operate the roller
shutter and has instructed them on how to use it.
2. Installation instructions
2.1 Safety rules
• Installation of the drive must only be carried out by suitably
qualified persons.
• The weight of the roller shutter must not exceed the load capacity
of the drive specified in the selection table.
• The proper way of laying the cable (loop pointing downwards)
further protects the drive from possible water damage.
• Do not drill holes in the motor housing.
• Protect the engine from contact with any fluid.
• Avoid crushing, hitting the motor and protect the motor from
falling.
• Do not connect more than one switch to one motor.
• Do not connect more than one motor to one switch.
Figure 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the YYGL Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Inel YYGL Series

  • Page 1 2 Accident prevention provisions. 1.3 General comments on hazards and safety measures The specified notes are general guidelines when using INEL devices in combination with other devices. These indications must be strictly adhered to when installing and operating the devices.
  • Page 2 2.2 Engine assembly • Attach the mounting bracket (A) to the side of the roller shutter 3. Adjustment of limit switches • Connect the adapter (D) to the motor drive ring (C) • In order to set the end positions of the roller shutter, the Place the carrier (E) on the motor shaft and secure it with the pin electromechanical limit switches must be adjusted.
  • Page 3 The full text of the EU Declaration of Conformity is available at specially designated place and, after recycling, can be used as a raw www.inel.gda.pl. material for reuse. VERSION OF INSTRUCTIONS 3/2024 Przedsiębiorstwo Informatyczno-Elektroniczne INEL Sp. z o.o., ul. Mostowa 1, 80-778 Gdańsk | inel@inel.gda.pl | www.inel.gda.pl...

This manual is also suitable for:

Gm seriesYygl35sGm35sGm35shYygl35shYygl45s ... Show all