Renzetti Presentation 2000 Series Quick Start Manual

Note:
We urge you to take time to familiarize yourself with the mechanics of
your presentation vise. Rotary tying can be easier and more productive
see tips (opposite page). Please return your warranty card to validate
your warranty.
Vise Assembly:
Your vise has been assembled and lubricated at the factory. All you have to do
is attach it to your existing c-clamp or pedestal base as shown below. The jaws
on your vise have been hardened and treated with a mil-spec corrosion resistant
coating. After use they should be coated with oil or a rust inhibitor like WD-40
to prevent rust or oxidation caused by acidity in your fingers.
Please note, our warranty does not cover rust damage.
1. Loosen stem lock screw enough to prevent interference with stem. Slide stem into the hole
of pedestal base and secure the stem by tightening the stem lock screw.
2. Slide cradle support collar onto pedestal stem as shown below. (flat side up)
3. Place cradle support on stem as shown.
4. Place the vise onto the stem so the head of the hinge screw (24) is facing you. Install the screw
and tighten. Note The tightness of this screw, will set the hinge presure of the vise head.
5. Slide cradle arm into the hole in the cradle support and secure.
6. Slide cradle support and cradle support collar up or down on stem so that the cradle is
on the center line of the rotary shaft as shown below.
7. Loosen the stem lock screw to turn the vise to the desired position.
Rotary Tension Knob
Cradle Tension Screw
Cradle Support
Cradle Support Collar
Stem Lock Knob
S.W. Stem Support
Cradle Adjustments:
1. Always adjust the cradle arm so that the cradle is close to the eye of the hook.
This prevents having to wind up a lot of thread after rotary tying.
2. Use the cradle support tension screw to add a little drag to the cradle support
so that the cradle still swings relatively easy.
3. If the cradle is in an awkward position for you it can be rotated as shown in
detail 1. The cradle is fairly snug on the arm so be sure to firmly hold the wire
to prevent bending it.
04/14 P2006
Center Line
Rotary Shaft
Cradle
Cradle Arm Lock Knob
Cradle Arm
Deluxe Pedestal Base
Detail 1
Renzetti Presentation 2000 Series
Item Part No.
1 120-01055
2 240-24008
3 240-24006
4 130-03111
5 120-01008
6 240-24009
7 240-24013
8 120-01055
9 240-24004
10 240-24003
11 130-03053
12 240-24002
13 240-24011
14 240-24001
15 110-10113
Rotate
16 130-03024
17 240-24060
18 400-24032
19 400-24033
U.S. Patents No.5,169,079 & No.4,169,562
True Rotary
Model # P2006 Dlx Pedestal Base
Vise
5 8
3 10
12
2 4 7 9 11
1
15
6
25
24
28
26
27
37
29
33
31
34
32
36
35
Lubricate all threads and moving parts as needed.
Description Qty. Item Part No.
End cap screw 1 20 130-03038
End cap 1 21 130-03017
Crank arm assly 1 22 210-22010
Spring 1 23 120-01450
Primary knob lock screw 1 24 120-01149
Rotary shaft primary knob 1 25 240-24005
Rotary shaft delrin washer 1 26 290-40255
Rotary housing lock screw 1 27 110-00003
Rotary head 1 28 250-40030
Rotary shaft housing 1 29 290-40263
Rotary shaft o-ring 1 30 290-40264
Primary rotary shaft 1 31 120-01043
Rotary shaft hinge screw 2 32 252-40162
Secondary rotary shaft 1 33 252-40167
Delrin tension button 1 34 290-40296
Ball bearing 1 35 120-01153
Cam 1 36 252-40135
Primary jaw
1 37 120-01147
Secondary jaw 1 240-24043
For the complete line of Renzetti products and
accessories. Please visit our website:
www.truerotary.com
21
19
16
17
20
18
13
14
22
23
30
Description Qty.
Jaw spring 1
Jaw o-ring 1
Jaw adjusting screw 1
Jaw mounting screw 1
Rotary head hinge screw 1
Rotary tension knob 1
Cradle support 1
Cradle arm lock screw 1
Stem 1 1
Cradle support collar 1 1
Cradle arm assembly 1 1
Stem lock stud 1 1
S W Stem support 1 1
Stem knob spacer 1
Stem lock knob 1
Ped. base mounting screw 1
Dlx. Pedestal Base Assembly 1
Cradle Tension Screw 1
Hex key set (not shown) 1
Made in the U.S.A.