Adjusting The Crossover Settings (X-Over); Setting Defeat; Volume Setting; Setting The Volume For Each Source - Alpine INE-S920HD Owner's Manual

3
To store the adjusted setting value, touch and hold
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
• Touch [Flat] to set all values to 0.0.
• If the Rear Speaker setting is "Off," the Rear Speaker setting cannot
be edited (Refer to page 47).
• If the Subwoofer setting is "Off, " the Subwoofer setting cannot be
edited (Refer to page 47).
Calling the Time Correction Value
Calling the pre-set time correction value.
Touch [Preset1], [Preset2], or [Preset3] on the time
correction screen.
The setting stored in the Preset will be recalled.
Adjusting the Crossover Settings (X-
OVER)
[X-OVER] is selected on the Sound setup menu in step 3. Refer to
"Sound Setup Operation" (page 47).
Before performing the following procedures, refer to "About the
Crossover" (page 52).
Setting item: X-OVER
1
Touch [Channel] to select the channel.
Each time you touch, the channel switches.
• The channel being adjusted is displayed in red.
Front HPF Rear HPF
2
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [ ] or [ ] of "Freq.," then select the cut-off
frequency.
Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) /
100 / 125 / 160 / 200 Hz
Adjusting the Slope
Touch [ ] or [ ] of "Slope," then adjust the HPF or LPF
slope.
Setting contents: 0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct
Adjusting the Level
Touch [ ] or [ ] of "Level," then adjust the HPF or LPF
level.
Setting contents: -12 to 0 dB (Initial setting: 0)
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
50
-EN
4
• Touch [Flat] to initialize all values.
• If the Rear Speaker setting is "Off," the Rear Speaker setting cannot
be edited (Refer to page 47).
• If the Subwoofer setting is "Off," the Subwoofer setting cannot be
edited (Refer to page 47).
• While adjusting the X-OVER you should consider the frequency
response of the connected speakers.
Calling the X-OVER adjusted value
Calling the pre-set X-OVER adjusted value.
Touch [Preset1], [Preset2], or [Preset3] on the X-
OVER screen.
The setting stored in the Preset will be recalled.

Setting Defeat

[Defeat] is selected on the Sound setup menu in step 3. Refer to "Sound
Setup Operation" (page 47).
If Defeat is "On," MX, Bass Max EQ, Download Sound Setting and
Parametric EQ functions are turned OFF. This disables any settings
made for these functions.
Setting item: Defeat
Setting content: Off (Initial setting) / On

Volume Setting

[Volume] is selected on the Sound setup menu in step 3. Refer to
"Sound Setup Operation" (page 47).
You can change the volume of the sound heard when a button is
touched.
Setting item: Key Sound Feedback
Setting contents: 0 to 7 (Initial setting: 4)
Subw. LPF

Setting the Volume for Each Source

[Source Volume Setup] is selected on the Sound setup menu in step 3.
Refer to "Sound Setup Operation" (page 47).
The volume level for each source can be adjusted.
Setting item: Radio / SiriusXM / DVD / CD / Compressed Media /
Setting contents: -14 to +14 (Initial setting: 0)
* BLUETOOTH Pandora correspond to BLUETOOTH Audio.
• Settable source differ depending on the connected device and
settings.
To store the adjusted setting value, touch and hold
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
iPod Music / iPod Video / Pandora / AUX / AUX3 /
BLUETOOTH Audio*