Advertisement
Instructions
MTX10UP01, MTX10UP02, MTX10UP05,
and MTX10UP07
Interface Module Installation
MTX100A MPEG Recorder & Player
075-0884-00
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com
075088400
075088400
www.valuetronics.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tektronix MTX10UP01
Summary of Contents for Tektronix MTX10UP01
- Page 1 Instructions MTX10UP01, MTX10UP02, MTX10UP05, and MTX10UP07 Interface Module Installation MTX100A MPEG Recorder & Player 075-0884-00 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so.
- Page 2 Copyright © Tektronix, Inc. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material.
-
Page 3: Service Safety Summary
Service Safety Summary Only qualified personnel should perform service procedures. Read this Service Safety Summary and the General Safety Summary in the product service manual or the user manual. Do Not Service Alone. Do not perform internal service or adjustments of this product unless another person capable of rendering first aid and resuscitation is present. - Page 4 Service Safety Summary MTX100A Interface Module Installation www.valuetronics.com...
-
Page 5: Kit Description
2), but the installation instructions are the same for all options. These instructions apply for the following upgrades: H MTX10UP01 (Option 01): adds the ASI interface module H MTX10UP02 (Option 02): adds the universal parallel/serial interface module H MTX10UP05 (Option 05): adds the IEEE1394/ASI interface module... -
Page 6: Kit Parts List
Kit Description Kit Parts List Circuit/figure number Quantity Part number Description MTX10UP01 (for Option 01) - - - - - - 1 ea 671-6118-00 CKT BD ASSY: A100 - - - - - - 1 ea 335-1365-00 MARKER, IDENT: MKD CONNECTORS FOR... -
Page 7: Installation Instructions
These instructions are for personnel who are familiar with servicing the product. If you need further details for disassembling or reassembling the product, refer to the MTX100A MPEG Recorder & Player Service Manual (Tektronix part number 071-1754-XX). CAUTION. To prevent static discharge damage, service the product only in a static-free environment. - Page 8 Installation Instructions Figure 1: Removing the instrument cabinet Removing the Right-side 1. Set the instrument so its left side is down on the work surface and its front is and Left-side Covers facing you. 2. Use a screwdriver with a T-10 Torx tip to remove the seven screws securing the right-side cover to the top and bottom of the chassis.
- Page 9 Installation Instructions Left-side cover Right-side cover Figure 2: Removing the right-side and left-side covers MTX100A Interface Module Installation www.valuetronics.com...
- Page 10 Installation Instructions Removing the Board 1. Set the instrument so its bottom is down on the work surface and its right Retainers side is facing you. 2. Use a screwdriver with a T-10 Torx tip to remove the two screws securing the board retainers to the chassis.
- Page 11 Installation Instructions Removing the Blank Panel 1. Use a screwdriver with a T-10 Torx tip to remove the two screws securing the blank panel to the side and rear of the chassis. See Figure 4. 2. Lift the blank panel away to remove it. See Figure 4. Save the screws. Blank panel Figure 4: Removing the blank panel MTX100A Interface Module Installation...
- Page 12 Installation Instructions CAUTION. Be careful not to damage the parts and cables of the interface module when you insert the module into the instrument. Installing the Interface 1. Insert the interface module into the card slot, paying attention to the module Module orientation.
- Page 13 Installation Instructions Installing the Board Use a screwdriver with a T-10 Torx tip to install each screw securing the board Retainers retainers to the chassis. Installing the Right-side 1. Use a screwdriver with a T-10 Torx tip to install the seven screws securing and Left-side Covers the right-side cover to the top and bottom of the chassis.
- Page 14 After you have installed the interface module in this kit, perform the functional check for the MTX100A as described in the MTX100A MPEG Recorder & Player Service Manual (Tektronix part number 071-1754-XX). g End of document g MTX100A Interface Module Installation...
Need help?
Do you have a question about the MTX10UP01 and is the answer not in the manual?
Questions and answers