NetZero Kalfire E-one 100F Installation And Operation Manual

Hide thumbs

Table Of Contents

Quick Links

Download this manual

INSTALLATION AND OPERATION MANUAL

Please read these instructions completely before

installing or operating the E-one fireplace.

NetZero Kalfire E-one Electric Fireplace

Models: AA-11-05388 – E-one 100F

AA-11-05387 – E-one 130F

IMPORTANT

Please read these instructions carefully before installation.

Failure to follow them could result in serious injury.

This appliance must be installed by a qualified installer.

The installation and wiring connections must be done in accordance with the

national and local codes having jurisdiction.

For use with 120V 60Hz electrical supply only.

This appliance must be grounded.

The heater outlet becomes hot while in operation.

Never cover the heater outlet or any other part of the appliance.

SAVE THESE INSTRUCTIONS

85-03-01324

Table of Contents

Need help?

Do you have a question about the Kalfire E-one 100F and is the answer not in the manual?

Questions and answers

Summary of Contents for NetZero Kalfire E-one 100F

Page 1 For use with 120V 60Hz electrical supply only. This appliance must be grounded. The heater outlet becomes hot while in operation. Never cover the heater outlet or any other part of the appliance. SAVE THESE INSTRUCTIONS 85-03-01324 NetZero Fireplace ©2024 All rights reserved. 0425...
Page 3: Table Of Contents
6.15 Connecting other Users 7 MAINTENANCE 7.1 Cleaning The Fireplace 7.2 Cleaning The Glass Reflector 8 WARRANTY 9 TECHNICAL DATA 9.1 Specifications Table of contents 9.2 Serial Number Label 1 INTRODUCTION 9.3 Wire Diagram 1.1 Receiving Inspection 9.4 Dimension Drawing 1.2 Certification 2 GENERAL SAFETY REGULATIONS 2.1 Additional General Safety Regulations for...
Page 4: Introduction
Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part NetZero Fire stands for innovation and quality. This is why 15 of the FCC Rules. These limits are designed to provide...
Page 5: General Safety Regulations
safely and understand the dangers. Children three to seven years old must not clean the GENERAL SAFETY REGULATIONS fireplace or perform user maintenance. If the power lead becomes damaged, • IMPORTANT INSTRUCTIONS it must be replaced by the supplier or another When using electrical appliances, necessary precautions qualified service provider to avoid danger.
Page 6: Additional General Safety Regulations For Atmos Heating
Do not install electronics, artwork, or any other • item that can be damaged from heat rising from the heater above the heater. NetZero Fire will not be responsible for any damage to these items. Furniture, curtains, and other combustible •...
Page 7: Assembly Of The Fireplace
Description 50-06-00164 ADJUSTABLE LEG, STOVE 40-03-00109 GLOVE, DISPOSABLE FOOD SERVICE, PK 100, 9737T28 85-03-01324 NetZero E-one 100-130 Manual 65-06-00367 MAGNET, T-40, 1-7/8 L X 7/8 Wx 3/8 Deep 50-02-00310 SCREW, ALLOY SOCKET HEAD M6 50-03-00076 NUT, 10-24 HEX FLANGE BLK ZINC...
Page 8 After rotating the screens forward ensure both sides are locked into the spring clips. Make sure the rear screen mask Use 4 (M6x8) screws to attach the rear screen to the bracket. Remove the protective film from the screen. is still in position. Remove the protective film from the rear screen mask.
Page 9: Top Screen Assembly
Replace the rear and top panels with 14 (M5 x 10) screws. Top Screen Assembly The fireplace in now ready to be installed into your wall. Remove the protective film from the top screen before installing it into the fireplace. The pegs at the front of the screen rest on brackets as shown below.
Page 10: Installing The Fireplace
INSTALLING THE FIREPLACE Setting up the fireplace Light / Illumination Place the fireplace in its final position before continuing to set up the fireplace. Level the fireplace using the adjustable The E-one functions on the basis of hologram technology. legs. Once you have levelled the fireplace, it is strongly This involves the use of a glass reflector that is placed at an recommended that you attach it to the wall using the wall angle in the fireplace.
Page 11: Wall Dimensions
Temperatures above the heat outlet on the fireplace can reach up to 150°F. Materials used in this area must be rated for these temperatures. NetZero Fire is not responsible for damage to walls because of the use of improper materials or installation.
Page 12: Mantel And Tv Height
The recess in the wall must comply with the framing dimensions and be at least 6” above the fireplace heater. Attention: NetZero Fireplace is not responsible for any damage to electronics or sensitive materials installed above the fireplace.
Page 13: E100 Log Set Installation
A letter is moulded on the bottom of each log to make identifying the log easy. Start the log set installation by placing the first three logs in the ember bed as shown. Place lava stones on the ember bed around these three logs. 85-03-01324 NetZero Fireplace ©2024 All rights reserved. 0425...
Page 14 Next, place the two larger logs “A” and “B” on the stands at the rear of the fireplace. These logs have cut outs on them that will fit over the stands. Place the smaller logs “E” and “I” on the ember bed as shown. Before placing more logs sprinkle the vermiculite over the ember bed.
Page 15: 4.4 E130 Log Set Installation
4.4 E130 Log Set Installation The logs are made of fragile material. Therefore, proceed with extreme caution when installing the logs. NOTE: Log set instructions are shown with the flat bottom floor installed in the fireplace. When installing the log set it is important that the logs are placed exactly as shown in these instructions. If logs are not placed correctly the projected flame will not line up with the logs.
Page 16 Place the next three logs on the ember bed as shown. Next, place log “K” on the right side of the ember bed. Log “O” is placed so that it is resting on log “P”. The placement of logs “P” and “O”...
Page 17: Placing Glass Reflector
Placing Upper Side Walls Placing Glass Reflector Install the magnets against the guide and slide into the groove of the bottom panel as shown below. Install the side walls by placing the bottom point against the extrusion on the glass reflector. Then rotate the side wall towards the wall and the magnet will hold it in place.
Page 18 Wear the included gloves to handle the front window. Place the front window into the two holders at the front of the fireplace. Then rotate the window up. Slide the loosened clips up so that the window can be positioned against the top of the fireplace.
Page 19: One Operation
E-ONE OPERATION Remote Control Pairing With the E-one you can create your own fire experience When the fireplace is used for the first through the various functions and/or options. time, the remote control will connect to the fireplace automatically. If the Main On/Off Switch following symbol is projected on the Power to the fireplace can be switched On/Off using the...
Page 20 Switching the Fireplace Off Press and hold the power button for two seconds to shut the fireplace completely off. Sound Choose between the full-bodied crackling sound of pine wood or the calmer and relaxing sound of beech wood. The sound of burning wood in combination with lifelike sparks enable a true sensory experience.
Page 21: Kalfire Connected App
KALFIRE CONNECTED APP Creating Account The Kalfire Connected app offers extended possibilities Open Kalfire Connected app and select skip/next on the compared to the remote control. images below. Installing the Kalfire Connected App Before installing the Kalfire Connected app, Please Check: •...
Page 22 Select one of the options and enter your information as prompted on the screen. Once you have entered your information in you will need to verify your email to create your account.
Page 23: Connecting App To Fireplace
Connecting App to Fireplace Wifi Connection After creating your account, it’s time to connect your Once on the Wi-Fi connection screen, make sure that the fireplace to the app. Wi-Fi connection is the same as the Wi-Fi that your phone is connected to.
Page 24: Adding New Fireplace To Connected App
Select “E-one” for the fireplace type. Adding New Fireplace to Connected App To add a new fireplace to the app. You need to select “connect a new fireplace”.
Page 25: Activate Bluetooth
Activate Bluetooth Bluetooth Mode Make sure Bluetooth is enabled. Once Bluetooth is enabled Put the fireplace remote into Bluetooth mode by pressing and you have the green check marks. Select “Continue” the flame appearance button for 7-10 seconds as shown in the image below.
Page 26: Selecting Bluetooth Device
Selecting Bluetooth Device Once your remote is in Bluetooth mode your fireplace will appear on the Bluetooth devices. Select the device, then select the device again to confirm your fireplace.
Page 27: Connecting The Fireplace To The Network
6.10 Connecting the Fireplace to the Network After connecting your fireplace via Bluetooth, you will need to connect the fireplace to your network. On the screen you should see your network on the connected app as shown below. Enter your network password and select “connect fireplace to a network.”...
Page 28: Pairing Fireplace To Connected App
6.11 Pairing Fireplace to Connected App Once in Bluetooth mode the screen will switch to the image below. Hold the flame appearance for 3 seconds, then press next on the Connected app. A green check mark will appear once you have successfully connected your fireplace to the app.
Page 29: Failure To Connect
6.12 Failure to connect 6.13 Adding Fireplace to the App If the red check mark appears on the connect app. Select Confirm the name or change the name of your fireplace and “Go Back” and repeat step 3.8 until the green check mark confirm to add your fireplace to the app as shown below.
Page 30: Fireplace Connected To App
6.14 Fireplace Connected to App Once the app is connected to the app the screen should appear as shown below. Now you will be able to control the fireplace with your app.
Page 31: Connecting Other Users
6.15 Connecting other Users To connect other users to the app repeat steps 3.1-3.2. Once you confirmed you’re on the same network. Select the fireplace name that applies to your fireplace. Repeat steps 3.8 until you have successfully connected the fireplace to the app and have the green check mark.
Page 32: Maintenance
MAINTENANCE Lean the top of the glass down and carefully remove it from CAUTION: Before cleaning, make sure the power has been the fireplace. The glass reflector can now be accessed and turned off at the circuit breaker panel and that the heating cleaned.
Page 33: Warranty
The serial number for the fireplace can be found inside the to all warranty claims. NetZero Fire is not responsible for fireplace on the left-hand side. To view the serial number results or costs of workmanship of unauthorized NetZero label, remove the front glass from the fireplace.
Page 34: Wire Diagram
Wire Diagram...
Page 35: Dimension Drawing
Dimension Drawing For framing the fireplace follow the framing dimensions and instructions given in this manual. Warning: The ceiling of the enclosure must be at least 6” above the top of the heater or 11 ½” above the top of the fireplace.
Page 36 1155 Sherman Rd, Hiawatha, IA 52233 (800)553-5422 NetZero is a manufactureer and distributor of these products, which are designed by Kalfire B.V. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND SUPPLIED MANUALS. IMPLIED WARRANTIES OF MERCHANTABILITY, IMPLIED WARRANTIES OF FITNESS, IMPLIED...

This manual is also suitable for:

Kalfire e-one 130f Aa-11-05388 Aa-11-05387