Download
Share
Print this page
  1. Manuals
  2. Brands
  3. NetZero Manuals
  4. Indoor Fireplace
  5. Kalfire E-one AA-11-05388 - E-one 100F
  6. Installation and operation manual

NetZero Kalfire E-one AA-11-05388 - E-one 100F Installation And Operation Manual

Hide thumbs Also See for Kalfire E-one AA-11-05388 - E-one 100F:

Advertisement

Quick Links

Download this manual
INSTALLATION AND OPERATION MANUAL
Please read these instructions completely before
installing or operating the E-one fireplace.
NetZero Kalfire E-one Electric Fireplace
Models: AA-11-05388 – E-one 100F
IMPORTANT
Please read these instructions carefully before installation.
Failure to follow them could result in serious injury.
This appliance must be installed by a qualified installer.
The installation and wiring connections must be done in accordance with the
national and local codes having jurisdiction.
For use with 120V 60Hz electrical supply only.
This appliance must be grounded.
The heater outlet becomes hot while in operation.
Never cover the heater outlet or any other part of the appliance.
SAVE THESE INSTRUCTIONS
85-03-01271
NetZero Fireplace ©2023 All rights reserved. 0623

Advertisement

loading
Need help?

Need help?

Do you have a question about the Kalfire E-one AA-11-05388 - E-one 100F and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for NetZero Kalfire E-one AA-11-05388 - E-one 100F

Summary of Contents for NetZero Kalfire E-one AA-11-05388 - E-one 100F

  • Page 1 For use with 120V 60Hz electrical supply only. This appliance must be grounded. The heater outlet becomes hot while in operation. Never cover the heater outlet or any other part of the appliance. SAVE THESE INSTRUCTIONS 85-03-01271 NetZero Fireplace ©2023 All rights reserved. 0623...
  • Page 2 Table of contents 1 INTRODUCTION 1.1 Receiving Inspection 1.2 Certification 2 GENERAL SAFETY REGULATIONS 2.1 Additional General Safety Regulations for Atmos Heating 2.2 Disposal 2.3 California Proposition 65 Warning 3 ASSEMBLY OF THE FIREPLACE 3.1 Required Tools 3.2 Included Hardware 3.3 Removal of Covers 3.4 Adjustable Feet 3.5 Rear Screen Assembly...
  • Page 3 However, there is no NetZero Fire stands for innovation and quality. This is why guarantee that interference will not occur in a particular we work continuously on the further development of our installation.
  • Page 4 Do not install electronics, artwork, or any other humidity must be <85%. item that can be damaged from heat rising from the heater above the heater. NetZero Fire will not • Do not place the fireplace directly under a wall be responsible for any damage to these items.
  • Page 5 ASSEMBLY OF THE FIREPLACE Rear Screen Assembly Install the rear screen bracket to the top LED rear screen Required Tools bracket. Use 2 (M5 x 10) screws. - 8mm Nut Driver or Socket - 5mm Allen Wrench - 3mm Allen Wrench - 12mm Wrench - 17mm Wrench - Level...
  • Page 6 Install the rear screen assembly in the back of the fireplace. Top Screen Assembly The bracket fits into slots at the back of the fireplace and Remove the protective film from the top screen before will rotate forward into the spring clips at the top. installing it into the fireplace.
  • Page 7 INSTALLING THE FIREPLACE Ventilation Openings The chase the fireplace is installed in must have sufficient ventilation for the fireplace to function correctly. A Light / Illumination minimum of 15 ½ in (100 cm ) of free area is required. The E-one functions on the basis of hologram technology. One way to accomplish the required ventilation is to cut a This involves the use of a glass reflector that is placed at an hole in the chase and install a 10”...
  • Page 8 Temperatures above the heat outlet on the fireplace can reach temperatures up to 175°F. Materials used in this area must be rated for these temperatures. NetZero Fire is not responsible for damage to walls because of the use of improper materials or installation.
  • Page 9 SETTING UP THE FIREPLACE (Optional) Placing Design Bottom Plates Place the fireplace in its final position before continuing to Please note: If a flat bottom plate was chosen, this step can be skipped. set up the fireplace. The design bottom plates are made of fragile Level the fireplace using the adjustable legs.
  • Page 10 Placing Lower Sidewalls The left lower sidewall has a 2 cut into the top flange of the part. The right lower sidewall has a 4 cut into the top flange of the part. The sidewalls are installed over a threaded stud on the wall of the fireplace.
  • Page 11 Start the log set installation by placing the first three logs on the ember bed as shown. Place lava stones on the ember bed around these three logs. Next place the two larger logs “A” and “B” on the stands at the rear of the fireplace. These logs have cut outs on them that will fit over the stands.
  • Page 12 Placing Glass Reflector Placing Upper Side Walls Install the upper side walls in the fireplace. The left-side wall has a 1 cut out in the top flange of the part. The right-side wall has a 3 cut out in the top flange of the part. Install the side walls by placing the bottom point against the extrusion on the glass reflector.
  • Page 13 Placing Front Window Tighten the screws on the clips so they are snug. Do not overtighten the screws. Loosen the screws to slide the retaining clips up. Do not remove the screws. Wear the included gloves to handle the front window. Place the front window into the two holders at the front of the fireplace.
  • Page 14 E-ONE OPERATION Remote Control Pairing With the E-one you can create your own fire experience When the fireplace is used for the first through the various functions and/or options. time, the remote control will connect to the fireplace automatically. If the Main On/Off Switch following symbol is projected on the Power to the fireplace can be switched On/Off using the...
  • Page 15 Anti-Reflect Function E-One Remote and Symbols When the fireplace is on briefly press the power button to turn the fireplace off with the anti-reflect mode activated. In this standby mode, the fireplace will be attractively lit. This provides a nice view of the logs, even when the fire is Atmos Heating (ON/OFF switch) not burning.
  • Page 16 MAINTENANCE Lean the top of the glass down and carefully remove it from the fireplace. The glass reflector can now be accessed and CAUTION: Before cleaning, make sure the power has been cleaned. turned off at the circuit breaker panel and that the heating element of the heater is cool.
  • Page 17 NetZero Fire dealer if pre-approved by NetZero Fire, is fireplace. responsible for all infield diagnosis and service work related to all warranty claims. NetZero Fire is not responsible for results or costs of workmanship of unauthorized NetZero Fire dealers or agents in the negligence of their service work.
  • Page 18 Wire Diagram...
  • Page 19 Dimension Drawing For framing the fireplace follow the framing dimensions and instructions given in this manual. Warning: The ceiling of the enclosure must be at least 6” above the top of the heater or 11 ½” above the top of the fireplace.
  • Page 20 1155 Sherman Rd, Hiawatha, IA 52233 (800)553-5422 NetZero is a distributor of these products, which are designed and manufactured by Kalfire B.V. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND SUPPLIED MANUALS. IMPLIED WARRANTIES OF MERCHANTABILITY, IMPLIED WARRANTIES OF FITNESS, IMPLIED...